單項選擇題

根據下圖,假設路由器已經配置了默認配置,那么這個接口是()。

A.Ethernet
B.Fast Ethernet
C.Gigabit Ethernet
D.asynchronous serial
E.synchronous serial


您可能感興趣的試卷

你可能感興趣的試題

1.多項選擇題Why do large OSPF networks use a hierarchical design?()

A.to confine network instability to single areas of the network.
B.to reduce the complexity of router configuration
C.to speed up convergence
D.to lower costs by replacing routers with distribution layer switches
E.to decrease latency by increasing bandwidth
F.to reduce routing overhead

3.多項選擇題

Host1正在試圖和Host2聯系。RouterC的e0接口是down的,以下選項正確的是?()


A.RouterC會使用ICMP通知Host1“Host2無法到達”
B.RouterC會使用ICMP通知Host1“Host1無法到達”
C.RouterC會使用ICMP通知Host1,RouterA和RouterB“Host2無法到達”
D.RouterC會發送一個“DestinationUnreachable”的消息類型
E.RouterC會發送一個“RouterSelection”的消息類型
F.RouterC會發送一個“SourceQuench”的消息類型

4.單項選擇題How many subnets can be gained by subnetting 172.17.32.0/23 into a /27 mask, and how many usable host addresses will there be per subnet?()

A.8 subnets, 31 hosts
B.8 subnets, 32 hosts
C.16 subnets, 30 hosts
D.16 subnets, 32 hosts
E.A Class B address can't be subnetted into the fourth octet.

6.單項選擇題

S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?()

A.Configure the no ip subnet-zero command on R1, R2, and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.

8.單項選擇題What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-treetopology?()

A.lowest port MAC address
B.port priority number and MAC address.
C.VTP revision number
D.highest port priority number.
E.pathcost

9.單項選擇題A network administrator wants to add a line to an access list that will block only Telnet access by the hosts on subnet 192.168.1.128/28 to the server at 192.168.1.5.What command should be issued to accomplish this task?()

A.access-list 101 deny tcp192.168.1.1280.0.0.15192.168.1.50.0.0.0eq23 access-list 101 permit ip any any
B.access-list 101 deny tcp192.168.1.1280.0.0.240192.168.1.50.0.0.0eq23 access-list101permit ip any any
C.access-list 1 deny tcp192.168.1.1280.0.0.255192.168.1.50.0.0.0eq21 access-list1permit ip any any
D.access-list 1 deny tcp192.168.1.1280.0.0.15host192.168.1.5eq23 access-list1permit ip any any

10.單項選擇題

一個網絡管理員配置了兩臺交換機London和Madrid,讓它們使用VTP。但是,兩臺交換機之間沒有共享VTP信息,根據下圖,回答交換機之間沒有分享VTP信息的原因是()。

A.VTP版本配置錯誤
B.VTP工作模式配置錯誤
C.VTP域名配置錯誤
D.VTP的pruning mode被禁止了
E.VTP的V2 mode被禁止了
F.VTPtraps generation被禁止了

最新試題

請參見圖示。在網絡中,PC1向PC2發送了一條消息。PC2收到的幀如圖所示。該幀中的哪一信息確定了正確的目的應用程序?()

題型:單項選擇題

請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是,從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題?()

題型:單項選擇題

請參見圖示。主機A 和B 無法互相通信。此問題的原因是什么?()

題型:單項選擇題

請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口?()

題型:單項選擇題

請參見圖示。某用戶想要查看當前的配置。圖中所示為ipconfig/all 命令的輸出。從此輸出可以得到哪三項結論?()

題型:多項選擇題

請參見圖示。主機B 嘗試與主機C 建立TCP/IP 會話。在嘗試期間,San Francisco 器由器的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為10.10.1.2而目的IP 地址為10.31.1.20的數據包。捕獲該幀時,它的目的MAC 地址是什么?()

題型:單項選擇題

PC 無法連接到任何遠程網站,無法ping 通其默認網關,也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常?()

題型:單項選擇題

路由器使用哪一項信息來確定源主機和目的主機之間的路徑?()

題型:單項選擇題

傳輸層如何讓主機能同時針對不同應用程序維護多個通信流?()

題型:單項選擇題

請參見圖示。下列哪組設備僅包含中間設備?()

題型:單項選擇題