單項選擇題A network administrator wants to add a line to an access list that will block only Telnet access by the hosts on subnet 192.168.1.128/28 to the server at 192.168.1.5. What command should be issued to accomplish this task?（）

A.access-list 101 deny tcp 192.168.1.128 0.0.0.15 192.168.1.5 0.0.0.0 eq 23  access-list 101 permit ip any any
B.access-list 101 deny tcp 192.168.1.128 0.0.0.240 192.168.1.5 0.0.0.0 eq 23  access-list 101 permit ip any any
C.access-list 1 deny tcp 192.168.1.128 0.0.0.255 192.168.1.5 0.0.0.0 eq 21  access-list 1 permit ip any any
D.access-list 1 deny tcp 192.168.1.128 0.0.0.15 host 192.168.1.5 eq 23  access-list 1 permit ip any any



您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題Which spread spectrum technology does the 802.11b standard define foroperation？（）

A.IR
B.DSSS
C.FHSS
D.DSSS and FHSS
E.IR，F(xiàn)HSS，and DSSS

3.單項選擇題Refer to the exhibit,a network administrator cannot establish a telnet session with the indicated router.What is the cause of this failure?（）

A.A level 5 password is not set
B.The vty password is missing
C.The console password is missing
D.An ACL is blocking Telnet access

4.多項選擇題Which two subnetworks would be included in the summarized address of 172.31.80.0 /20？ （）

A.172.31.17.4/30
B.172.31.51.16/30
C.172.31.64.0/18
D.172.31.80.0/22
E.172.31.92.0/22
F.172.31.192.0/18

5.多項選擇題Which can be done to secure the virtual terminal interfaces on a router?（）

A.Administratively shut down the interfaces.
B.Physically secure the interfaces.
C.Configure a virtual terminal password and login process.
D.Enter an access list and apply it to the terminal interfaces using the access-class command.
E.Create an access list and apply it to the terminal interfaces using the access-group command.

6.單項選擇題

Refer to the exhibit. Which statement describes DLCI 17？（）

A.DLCI 17 describes the ISDN circuit between R2 and R3.
B.DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
C.DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D.DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.

7.單項選擇題A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next？（）

A.It checks the configuration register
B.It attempts to boot from a TFTP server
C.It loads the first image file in flash memory
D.It inspects the configuration file in NVRAM for boot instructions

8.單項選擇題Which item represents the standard IP ACL?（）

A.access-list 50 deny 192.168.1.1 0.0.0.255
B.access-list 110 permit ip any any
C.access-list 2500 deny tcp any host 192.168.1.1 eq 22
D.access-list 101 deny tcp any host 192.168.1.1

9.單項選擇題Which command enables IPv6 forwarding on a cisco router？（）

A.ipv6 host
B.ipv6 unicast-routing
C.ipv6 local
D.ipv6 neighbor

10.單項選擇題A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）

A.For the two vlans to communicate，a network statement for the trunk interface needs to be added to the  OSPF configuration.
B.For the two vlans to communicate， a network statement for each subinterface needs to be  added  to the OSPF configuration.
C.Direct inter-vlan communication does not require OSPF
D.OSPF cannot be used if router-on-a-stick is configured on the router