A.NCP
B.LCP
C.ISDN
D.DLCI
E.SLIP
您可能感興趣的試卷
你可能感興趣的試題
What can be determined from the line of show ip route output shown in the exhibit？（）
A. The next routing update can be expected in 35 seconds.
B. The IP address 10.10.10.6 is configured on S0/1.
C. The IP address 10.10.10.8 is configured on S0/1.
D. This route is using the default administrative distance.
E. The 10.10.10.8 network is two hops away from this router.
A.Microsegmentation decreases the number of collisions on the network.
B.if a switch receives a frame for an unkown destination,it uses ARP to resolve the address.
C.Spanning Tree Protocol allows switches to automatically share vlan information.
D.In a properly functioning network with redundant switched paths,each switched aegment will contain one root bridge with all its ports in the forwarding state.All other switches in that broadcast domain will have only one root port.
E.Establishing vlans increases the number of broadcast domains.
F.Switches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally， static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes？（）
A.Configure the no ip subnet-zero command on R1,R2,and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
Which destination addresses will be used by Host A to send data to Host C？（）
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router’s E0 interface
F. the MAC address of the router’s E0 interface
An administrator is unsuccessful in adding VLAN 50 to a switch. While troubleshooting the problem，the administrator views the output of the show vtp status command， which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database？（）
A. Switch（config-if）# switchport access vlan 50
B. Switch（vlan）# vtp server
C. Switch（config）# config-revision 20
D. Switch（config）# vlan 50 name Tech
E. Switch（vlan）# vlan 50
F. Switch（vlan）# switchport trunk vlan 50
A.10.188.31.0/27
B.10.188.31.0/26
C.10.188.31.0/29
D.10.188.31.0/28
E.10.188.31.0/25
Refer to the exhibit.A network technician is asked to design a small network with redundancy. The exhibit represents this design， with all hosts configured in the same VLAN. What conclusions can be made about this design？（）
A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.
A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2.
A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan
Refer to the exhibit.After a RIP route is marked invalid on Router_1， how much time will elapse before that route is removed from the routing table？（）
A.30 seconds
B.60 seconds
C.90 seconds
D.180 seconds
E.240 seconds
最新試題
請參見圖示。從主機X 發出的到主機Y 的tracert 命令已成功。下列哪一項正確地反映了追蹤列表中顯示的中間網絡設備的順序？（）
請參見圖示。在網絡中，PC1向PC2發送了一條消息。PC2收到的幀如圖所示。該幀中的哪一信息確定了正確的目的應用程序？（）
請參見圖示。某用戶想要查看當前的配置。圖中所示為ipconfig/all 命令的輸出。從此輸出可以得到哪三項結論？（）
OSI 哪一層可提供有序的數據重構服務？（）
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是，從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€邏輯地址范圍？（）
PC 無法連接到任何遠程網站，無法ping 通其默認網關，也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常？（）
請參見圖示。網絡中的主機A 正在向主機B 發送數據段。有關所交換的數據段的流量控制如圖所示。下列關于此通信的陳述，哪兩項是正確的？（）
在配置路由器時，網絡技術人員想要命名路由器。輸入hostname 命令后，技術人員會看到下列哪一項提示？（）
在路由器上使用Router#copy running-config startup-config 命令會產生什么效果？（）