Refer to the exhibit. Look at the command output. Assume that there is no other path， and the configuration is correct. What would be the consequences of this situation？（）
A. Users in SW1 can ping SW2 but not vice versa.
B. Users in SW2 can ping SW1 but not vice versa.
C. Users in SW1 and SW2 can ping each other.
D. Users in SW1 and SW2 cannot ping each other.
您可能感興趣的試卷
你可能感興趣的試題
A.to prevent multicast packets from looping
B.to prevent PIM packets from looping
C.to instruct PIM where to send a （*， G） or （S， G） join message
D.to prevent multicast packets from looping and to instruct PIM where to send a （*， G） or （S， G） joinmessage
A.232.0.0.0/8
B.239.0.0.0/8
C.232.0.0.0/4
D.FF3x：：/32
E.FF2x：：/32
F.FF3x：：/16
Refer to the exhibit. Look at the command output. What would be the most probable reason for this port-ID mismatch？（）
A. spanning-tree misconfiguration
B. speed mismatch configuration
C. cabling problem
D. configuration problem
A.PIM-SM
B.PIM-DM
C.PIM-SSM
D.DVMRP
A. Incorrect VTP domain
B. Incorrect VTP password
C. Incorrect VTP mode
D. Incorrect VTP configuration revision
A. Clear the MAC address table in the switch.
B. Clear the ARP cache in the switch.
C. Clear the ARP cache in the end devices.
D. Clear the ARP cache in the application servers.
A.Forwarding Address
B.External Route
C.Reference Link-State ID
D.Option
E.Prefix Options
A. The trunking configuration mode on Switch1 is set to Off.
B. The trunking configuration mode on the other end is set to On.
C. The trunking configuration mode on the other end is set to Desirable.
D. Cisco Discovery Protocol is not running on the other end.
E. There is a VTP domain name mismatch.
F. Switch1 does not support 802.1Q
A.It allows the standby RP to take control of the device after a hardware or software fault on the active RP.
B.It is a Layer 3 function that works with SSO to minimize the amount of time a network is unavailable tousers following a switchover.
C.It is supported by the implementation of EIGRP， OSPF， RIPv2， and BGP protocols.
D.It synchronizes startup configuration， startup variables， and running configuration.
E.The main objective of NSF is to continue forwarding IP packets following a switchover.
F.Layer 2 802.1w or 802.1s must be used， as 802.1d cannot process the Layer 2 changes.
G.Routing protocol tuning parameters must be the same as the NSF parameters， or failover will beinconsistent.
A. The VSS switch must be the root bridge for all VLANs and is automatically designated
B. The VSS switch is defined in RFC 4318 as a managed object
C. The PAgP+ or LACP protocols are used to maintain the operational state of the VSS devices
D. A VSS interoperates with a virtual port channel
E. The 802.1Q or ISL protocols are used to maintain the operational state of the VSS devices
F. A VSS increases the size of the spanning-tree domain
最新試題
Which of the following is true about the MPLS header and its EXP field size？（）
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）
Spanning Tree Protocol IEEE 802.1 s defines the ability to deploy which of these？（）
You are the network administrator of an enterprise with a main site and multiple remote sites. Your networkcarries both VOIP and data traffic. You agree with your service provider to classify VOIP and data trafficaccording to the different service RFCs. How can your data and VOIP traffic be marked？（）
All of these are fundamental building blocks of differentiated services Traffic Conditioner Block exceptwhich one？（）
How does an IPv6 router deal with a packet that is larger than the outgoing interface MTU？（）
Which types of prefixes will a router running BGP most likely advertise to an IBGP peer， assuming it is notconfigured as a route reflector？（）
Which multicast address is reserved for cisco-rp-discovery？（）
In Layer 2 topologies， spanning-tree failures can cause loops in the network. These unblocked loops cancause network failures because of excessive traffic. Which two Catalyst 6500 features can be used to limitexcessive traffic during spanning-tree loop conditions？（）
In GLBP，which router will answer on client ARP requests？（）