A. BGP peers must be Layer 2-adjacent
B. EBGP multihop is not configured
C. The firewall is not configured to allow IP protocol 89
D. The firewall is not configured to allow UDP 179.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Users on the 199.155.24.0 network are unable to reach the 172.16.10.0 network. What is the most likely solution？（）
A. Router ISP1 should be configured to peer with router B
B. Router ISP2 should be configured with no synchronization
C. Router ISP1 should be configured with no synchronization
D. Router ISP2 should be configured with no auto-summary.
E. Router ISP1 or IPS2 should be configured with network 176.16.10.0 mask 255.255.255.0
A.It relies on IPv6 to do the fragmenting.
B.It splits the LS Update packet into smaller packets.
C.It splits the LSA into smaller router LSA packets.
D.It produces an error.
Refer to the exhibit. Routers A and B are directly connected and running OSPF， but they are unable to form a neighbor relationship. What is the most likely cause？（）
A. The routers are not on the same network.
B. The network statements do not match.
C. The process number does not match.
D. The MTU does not match.
E. The OSPF cost does not match.
F. There is a physical issue with the cable.
Refer to the exhibit. Routers A and B are directly connected and running EIGRP， but they are unable to form a neighbor relationship. What is the most likely cause？ （）
A. The network statements are misconfigured.
B. The IP address statements are misconfigured.
C. The autonomous system is misconfigured.
D. There is a physical issue with the cable.
Refer to the exhibit. Routers A and B are directly connected. Given the configuration， how many EIGRP routes will router B see in its routing table？（）
A. 0
B. 1
C. 2
D. 3
E. 4
A. LSA 1
B. LSA 3
C. LSA 4
D. LSA 5
E. LSA 7
A. They are used to summarize area routes to other areas.
B. They are used in not-so-stubby areas to propagate external routes.
C. They are used to notify areas of the ASBR.
D. They are flooded to all areas except stub areas （external route）.
A.00000
B.12345
C.23456
D.65000
E.99999
A. The Layer 2 multicast address of the destination node
B. The solicited node multicast address of the destination node
C. The Layer 2 address of the destination node based on the destination IPv6 address
D. The IPv6 address of the destination node based on the destination Layer 2 address
A.6to4
B.6over4
C.ISATAP
D.GRE
最新試題
Which three protocols or applications should be placed in a class that is configured with WRED？（）
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group？（）
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link，but only allow eachindividual flow to use 1 MB/s？（）
You are the network administrator of an enterprise with a main site and multiple remote sites. Your networkcarries both VOIP and data traffic. You agree with your service provider to classify VOIP and data trafficaccording to the different service RFCs. How can your data and VOIP traffic be marked？（）
What is also called Type 0 authentication in OSPF on Cisco Routers？（）
Which three options are valid ways to filter routes from a BGP peer？（）
Based on the exhibit presented. What will be the objective of this route map when applied to traffic passing through a router？（）
In Layer 2 topologies， spanning-tree failures can cause loops in the network. These unblocked loops cancause network failures because of excessive traffic. Which two Catalyst 6500 features can be used to limitexcessive traffic during spanning-tree loop conditions？（）
Which of the following is true about the MPLS header and its EXP field size？（）
When STP UplinkFast is enabled on a switch utilizing the default bridge priority， what will the new bridgepriority be changed to？（）