Refer to the exhibit. An administrator pings the default gateway at 10.10.10.1 and sees the output as shown. At which OSI layer is the problem?（）
A.data link layer
B.application layer
C.access layer
D.session layer
E.network layer
您可能感興趣的試卷
你可能感興趣的試題
A.Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B.Ensure that cables A and B are straight-through cables.
C.Ensure cable A is plugged into a trunk port.
D.Ensure the switch has power.
E.Reboot all of the devices.
F.Reseat all cables.
A.learning
B.listening
C.discarding
D.forwarding
A.HostA is not on the same subnet as its default gateway
B.The address of SwitchA is a subnet address
C.The Fa0/0 interface on RouterA is on a subnet that cannot be used
D.The serial interfaces of the routers are not on the same subnet
E.The Fa0/0 interface on RouterB is using a broadcast address
Refer to the exhibit。A problem with network connectivity has been observed.It is suspected that the cable connected to switch port Fa0/9 on Switch 1 disconnected.What would be an effect of tis cable being disconnected?（）
A.Host B would not be able to access the server in VLAN9 until the cable is reconnected
B.For less than a minute ,Host B would not be able to access the server in VLAN9.Then normal network function would resume.
C.Communication between VLAN3 and the other VLANs would be disabled
D.The transfer of files from Host B to the server in VLAN9 would be significantly slower.
Refer to the exhibit. The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? （）
A.Configure the gateway on Host A as 10.1.1.1.
B.Configure the gateway on Host B as 10.1.2.254.
C.Configure the IP address of Host A as 10.1.2.2.
D.Configure the IP address of Host B as 10.1.2.2.
E.Configure the masks on both hosts to be 255.255.255.224.
F.Configure the masks on both hosts to be 255.255.255.240.
Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem?（）
A.All of the routers need to be configured for backbone Area 1.
B.R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C.A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D.The hello and dead interval timers are not set to the same values on R1 and R3.
E.EIGRP is also configured on these routers with a lower administrative distance.
F.R1 and R3 are configured in different areas.
A.Router# show ip eigrp adjacency
B.Router# show ip eigrp topology
C.Router# show ip eigrp interfaces
D.Router# show ip eigrp neighbors
A.The command is accepted and the respective VLAN is added to vlan dat.
B.The command is rejected.
C.The command is accepted and you must configure the VLAN manually.
D.The port turns amber.
A.after broken links are re-established
B.in an improperly implemented redundant topology
C.when upper-layer protocols require high reliability
D.during high traffic periods
E.when a dual ring topology is in use
A.ping
B.tracert
C.ipconfig
D.show ip route
E.winipcfg
F.show interfaces
最新試題
Which three statements about the features of SNMPv2 and SNMPv3 are true?（）
What command visualizes the general NetFlow data on the command line?（）
Which three are the components of SNMP? （）
Which statement describes VRRP object tracking?（）
Refer to the exhibit.If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?（）
Which statement describes the process ID that is used to run OSPF on a router ?（）
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow?（）
Which three features are added in SNMPv3 over SNMPv2? （）
Refer to the exhibit.If the devices produced the given output,what is the cause of the EtherChannel problem?（）
What level will be trapped if the administrator executes the command ？（）