A.Enable VTP pruning on any switch in the management domain
B.Enable VTP pruning on any client switch in the domain
C.Enable VTP pruning on a VTP server in the management domain
D.Enable VTP pruning on every switch in the domain
E.None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
A.VTP version 2 supports Token Ring VLANs
B.VTP version 2 allows VLAN consistency checks
C.VTP version 2 allows active redundant links when used with spanning tree
D.VTP version 2 reduces the amount of configuration necessary
E.VTP version 2 saves VLAN configuration memory
A.VTP mode
B.VTP password
C.VTP revision number
D.VTP pruning
E.VTP domain name
F.None of the other alternatives apply
Refer to the exhibit. VTP has been enabled on the trunk links between all switches within the TEST domain. An administrator has recently enabled VTP pruning. Port 1 on Switch 1 and port 2 on Switch 4 are assigned to VLAN 2. A broadcast is sent from the host connected to Switch 1. Where will the broadcast propagate?（）
A.Every switch in the network receives the broadcast and will forward it out all ports.
B.Every switch in the network receives the broadcast，but only Switch 4 will forward it out port 2.
C.Switches 1，2，and 4 will receive the broadcast，but only Switch 4 will forward it out port 2.
D.Only Switch 4 will receive the broadcast and will forward it out port 2.
A.30 seconds
B.5 minutes
C.1 minute
D.10 seconds
E.5 seconds
F.None of the other alternatives apply
A.A root VTP server
B.A trunk port
C.VTP priority
D.VLAN 1
E.None of the other alternatives apply
A.STP root status
B.VTP mode
C.Negotiation status
D.Management domain
E.Configuration revision number
A.Devices use DHCP to request their VLAN.
B.Attached devices are unaware of any VLANs.
C.Devices are assigned to VLANs based on their MAC addresses.
D.Devices are in the same VLAN regardless of which port they attach to.
A.VMPS server lookup is required
B.Easy to configure
C.Easy of adds，moves，and changes
D.Based on MAC address of the connected device
Given the above partial configuration, which two statements are true about VLAN traffic?（）
A.VLANs 1-5 will use fa0/10 as a backup only.
B.VLANs 6-10 will use fa0/10 as a backup only.
C.VLANs 1-5 will be blocked if fa0/10 goes down.
D.VLANs 1-10 are configured to load share between fa0/10 and fa0/12.
E.VLANs 6-10 have a port priority of 128 on fa0/10.
A.Configuration revision number
B.Configuration revision flag field
C.Configuration revision reset switch
D.Configuration revision database
E.None of the other alternatives apply
最新試題
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）