A.IP ToS of 0xEF
B.IP experimental ECN
C.DSCP decimal 5
D.Binary value of 101110
您可能感興趣的試卷
你可能感興趣的試題
A.Cisco
B.ANSI-Annex D
C.Q.931-Annex B
D.Q.933-Annex A
A.An update packet with init flag set from a known, already established neighbor relationship was received by one of the routers.
B.The ARP cache was cleared.
C.The counters were cleared.
D.The IP EIGRP neighbor relationship was cleared manually.
A.hostname
B.loopback address
C.default gateway
D.domain name
E.SSH peer address
A.Configure the EtherChannel as "desirable" first.
B.Assign all interfaces to the same VLAN.
C.Disable PortFast on the interfaces in the EtherChannels.
D.Disable all interfaces first.
E.Fast Ethernet and Gigabit Ethernet ports cannot be assigned to the same EtherChannel.
F.Fix cabling problems.
A.Tunnel IPv6 over IPv4 to connect far-end IPv6 networks.
B.Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is not possible.
C.Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is possible.
D.What is the meaning of EUI-64 and how does it work?
E.Tunnel IPv4 over IPv6 to connect far-end IPv4 networks.
A.EIGRP will not be accepted when configured on the actual RIPv2 routers.
B.OSPF will no longer be used in the routing table, because you only have EIGRP internal routes running.
C.OSPF will no longer be used in the routing table, because you only have EIGRP external routes running.
D.RIPv2 will populate its RIP database but not its routing table, because you only have EIGRP external routes running.
E.RIPv2 will populate its RIP database but not its routing table, because you only have EIGRP internal routes running.
F.OSPF database will have RIPv2 routes.
A.The trunking configuration mode on Switch1 is set to Off.
B.The trunking configuration mode on the other end is set to On.
C.The trunking configuration mode on the other end is set to Desirable.
D.Cisco Discovery Protocol is not running on the other end.
E.There is a VTP domain name mismatch.
F.Switch1 does not support 802.1Q
A.BGP peers must be Layer 2-adjacent.
B.EBGP multihop is not configured.
C.The firewall is not configured to allow IP protocol 89.
D.The firewall is not configured to allow UDP 179.
A.route redistribution
B.import and export using route descriptors
C.import and export using route targets
D.Cisco MPLS Traffic Engineering
A.CEF
B.FIB
C.LFIB
D.IGP
最新試題
Which two attributes need to match for two switches to become members of the same MST region? ()
An administrator of a peer-to-peer server application reports that the maximum bandwidth that his application receives is 90 Mb/s. You have an 8-port,100-Mb/s EtherChannel bundle on the switching infrastructure between the two servers, resulting in a bidirectional throughput of more than what is recorded. Which two solutions would allow for more bandwidth for the application?()
In which way can the IPv6 address of 2031:0000:130F:0000:0000:09C0:876A:130B be expressed most efficiently?()
Which switch port error is an indication of duplex mismatches on 10/100/1000 IEEE 802.3u Gigabit Ethernet ports?()
Which three are needed to run VRF lite for IPv6 on a router? ()
You are the network administrator of a Layer 3 switched network. Users in one VLAN are complaining that access to the server VLAN is very slow from time to time. Traffic in the local VLAN works without any issue, and users in other VLANs do not have any complaint to reach the server VLAN. What is most likely the cause of this issue?()
Two directly connected routers, R1 and R2, are both configured for OSPF graceful restart. R2 is able to switch packets in hardware, but R1 is not. If a network administrator logs on to R2 and performs a system reload, which will be the result?()
For the following ports, which port is on every bridge in a Spanning Tree Protocol IEEE 802.1w network except the root bridge?()
When a BGP router is not capable of understanding 4-byte AS numbers, it will see 4-byte AS numbers as a special, reserved, 2-byte AS number in the AS path. Which 2-byte AS number is this reserved one?()
f a Cisco switch is configured with VTPv1 in transparent mode, what is done with received VTP advertisements?()