A. Router(config)#router ospf 1
B. Router(config)#router ospf 0
C. Router(config)#router ospf area 0
D. Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E. Router(config-router)#network 192.168.16.0 0.0.0.255 0
F. Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
您可能感興趣的試卷
你可能感興趣的試題
A. RIP requires less time to converge
B. RIP uses less bandwidth
C. RIP is less complex to configure
D. RIP demands fewer router resources
E. RIP has a more accurate metric
A. one IP network or subnetwork for each subinterface
B. subinterface numbering that matches vlan tages
C. subinterface encapsulation identifiers that match vlan tags
D. a management domain for each subinterface
E. one physical interface for each subinterface
F. one subinterface per vlan
A. A CSU/DSU terminates a digital local loop
B. A modem terminates a digital local loop
C. A CSU/DSU terminates an analog local loop
D. A modem terminates an analog local loop
E. A router is commonly considered a DTE device
F. A router is commonly considered a DCE device
A. can be used over analog circuits
B. maps Layer 2 to Layer 3 address
C. encapsulates several routed protocols
D. supports IP only
E. provides error correction
A. Administratively shut down the interfaces.
B. Physically secure the interfaces.
C. Configure a virtual terminal password and login process.
D. Enter an access list and apply it to the terminal interfaces using the access-class command.
E. Create an access list and apply it to the terminal interfaces using the access-group command.
A.multicast
B.broadcast
C.allcast
D.podcast
E.anycast
A.blocking
B.learning
C.disabled
D.forwarding
E.listening
A. Security increases because only the network administrator may change the routing tables.
B. Configuration complexity decreases as network size increases.
C. Routing updates are automatically sent to neighbors.
D. Route summarization iscompued automatically by the router.
E. Routing traffic load is reduced when used in stub network links
F. An efficient algorithm is used to build routing tables,using automatic updates.
G. Routing tables adapt automatically to topology changes.
A. to confine network instability to single areas of the network.
B. to reduce the complexity of router configuration
C. to speed up convergence
D. to lower costs by replacing routers with distribution layer switches
E. to decrease latency by increasing bandwidth
F. to reduce routing overhead
A.complicated header
B.plug-and-play
C.no broadcasts
D.checksums
E.optional IPsec
F.autoconfiguration
最新試題
Which statement describes the rule of split horizon?（）
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?（）
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）
At which layer of the OSI model dose PPP perform?（）
Which command displays the CHAP authentication process as it occurs between two routers?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
What is the subnetwork address for a host with the IP address 201.100.5.68/28?（）
A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?（）
Which protocol reduces administrative overhead in a switched network by allowing the configuration of a new VLAN to be distributed to all the switches in a domain?（）
Three access ports have been installed and configured to a small office.What term defines the wireless topology?（）