單項選擇題The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）

A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題A default Frame Relay WAN is classified as what type of physical network?（）

A. point-to-point
B. broadcast multi-access
C. nonbroadcast multi-access
D. nonbroadcast multipoint
E. broadcast point-to-multipoint

2.單項選擇題The following configuration line was added to router R1 Access-list 101 permit ip 10.25.30.0 0.0.0.255 any What is the effect of this access list configuration?（）

A. permit all packets matching the first three octets of the source address to all destinations
B. permit all packet matching the last octet of the destination address and accept all source addresses
C. permit all packet matching the host bits in the source address to all destinations
D. permit all packet from the third subnet of the network address to all destinations

3.單項選擇題The following access list below was applied outbound on the E0 interface connected to the 192.169.1.8/29 LAN: access-list 135 deny tcp 192.169.1.8 0.0.0.7 eq 20 any access-list 135 deny tcp 192.169.1.8 0.0.0.7 eq 21 any How will the above access lists affect traffic? （）

A. FTP traffic from 192.169.1.22 will be denied
B. No traffic, except for FTP traffic will be allowed to exit E0
C. FTP traffic from 192.169.1.9 to any host will be denied
D. All traffic exiting E0 will be denied
E. All FTP traffic to network 192.169.1.9/29 will be denied

5.單項選擇題A network administrator wants to add a line to an access list that will block only Telnet access by the hosts on subnet 192.168.1.128/28 to the server at 192.168.1.5. What command should be issued to accomplish this task?（）

A. access-list 101 deny tcp 192.168.1.128 0.0.0.15 192.168.1.5 0.0.0.0 eq 23 access-list 101 permit ip any any
B. access-list 101 deny tcp 192.168.1.128 0.0.0.240 192.168.1.5 0.0.0.0 eq 23 access-list 101 permit ip any any
C. access-list 1 deny tcp 192.168.1.128 0.0.0.255 192.168.1.5 0.0.0.0 eq 21 access-list 1 permit ip any any
D. access-list 1 deny tcp 192.168.1.128 0.0.0.15 host 192.168.1.5 eq 23 access-list 1 permit ip any any

7.單項選擇題What is one benefit of PVST+?（）

A. PVST+reduces the CPU cycles for all the switches in the network
B. PVST+automatically selects the root bridge location,to provide optimized bandwidth usage.
C. PVST+allow the root switch location to be optimized per vlan.
D. PVST+supports Layer 3 load balancing without loops.

8.單項選擇題Which item represents the standard IP ACL?（）

A. access-list 50 deny 192.168.1.1 0.0.0.255
B. access-list 110 permit ip any any
C. access-list 2500 deny tcp any host 192.168.1.1 eq 22
D. access-list 101 deny tcp any host 192.168.1.1

9.單項選擇題Which statement about access lists that are applied to an interface is true?（）

A. you can apply multiple access lists with the same protocol or in different direction.
B. you can config one access list,per direction,per layer 3 protocol
C. you can place as many access lists as you want on any interface
D. you can apply only one access list on any interface

10.單項選擇題Which command enables RSTP on a switch?（）

A. spanning-tree mode rapid-pvst
B. spanning-tree uplinkfast
C. spanning-tree backbonefast
D. spanning-tree mode mst