多項選擇題

The Company network utilizes the Multiple-instance Spanning Tree protocol in its switched LAN. 
 Which three statements about the MST protocol (IEEE 802.1S) are true? ()

A. To verify the MST configuration, the show pending command can be used in MST configuration  mode.
B. When RSTP and MSTP are configured; UplinkFast and BackboneFast must also be enabled.
C. All switches in the same MST region must have the same VLAN-to-instance mapping, but  different configuration revision numbers.
D. All switches in an MST region, except distribution layer switches, should have their priority  lowered from the default value 32768.
E. An MST region is a group of MST switches that appear as a single virtual bridge to adjacent  CST and MST regions.
F. Enabling MST with the "spanning-tree modemst" global configuration command also enables  RSTP.


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題

On switch R1 you issue the "udld enable" global command. 
What does this command accomplish? ()

A. Enables all fiber-optic LAN ports for Unidirectional LINK Detection (UDLD)
B. Enables all copper media LAN ports Unidirectional Link Detection (UDLD)
C. Overrides the default UDLS setting for all ports
D. Globally enables all ports on the device for Unidirectional Link Detection (UDLS)
E. None of the other alternatives apply

2.單項選擇題

Switch R1 has been configured with the root guard feature. 
What statement is true if the spanning  tree enhancement Root Guard is enabled? ()

A. If BPDUs are not received on a non-designated port, the port is moved into the STP loop- inconsistent blocked state
B. IF BPDUs are received on a PortFast enabled port, the port is disabled.
C. If superior BPDUs are received on a designated port, the interface is placed into the root- inconsistent blocked state.
D. If inferior BPDUs are received on a root port, all blocked ports become alternate paths to the  root bride.

3.多項選擇題

You are the network administrator tasked with designing a switching solution for the Company  network. 
Which of the following statements describing trunk links are INCORRECT?()

A. The trunk link belongs to a specific VLAN.
B. Multiple trunk links are used to connect multiple end user devices.
C. A trunk link only supports native VLAN.
D. Trunk links use 802.10 to identify a VLAN.
E. The native VLAN of the trunk link is the VLAN that the trunk uses for untagged packets.

4.多項選擇題

ISL is being configured on a Company switch. 
Which of the following choices are true regarding  the ISL protocol? ()

A. It can be used between Cisco and non-Cisco switch devices.
B. It calculates a new CRC field on top of the existing CRC field.
C. It adds 4 bytes of protocol-specific information to the original Ethernet frame.
D. It adds 30 bytes of protocol-specific information to the original Ethernet frame.

7.單項選擇題

You are the network administrator at Company and switch R1 is configured as shown below:  Interface gigethernet 0/1  Switchport mode trunk  
Switchport trunk encapsulation dot1q  Switchport trunk native vlan 5  
If untagged frames are arriving on interface gigethernet 0/1 of R1, 
which of the following statement  are correct?()

A. Untagged frames are automatically assumed to be in VLAN 5.
B. Untagged frames are defaulted to VLAN 1 traffic.
C. Untagged frames are dropped because all packets are tagged when dot1q trunked.
D. Untagged frames are determined on the other switch
E. Untagged frames are not supported on 802.1Q trunks.

8.多項選擇題

If you were to configure an ISL Ethernet trunk between two Cisco switches, named R1 and R2,  
what would you have to include at the end of the link for the trunk to operate correctly? ()

A. An identical VTP mode.
B. An identical speed/duplex.
C. An identical trunk negotiation parameter.
D. An identical trunk encapsulation parameter.

10.單項選擇題

You need to connect two Company core switches via an ISL trunk. 
Which statement is true  regarding the configuration of ISL trunks? ()

A. A Catalyst switch cannot have ISL and IEEE 802.1q trunks enabled.
B. All Catalyst switches support ISL trunking.
C. A Catalyst switch will report giants if one side is configured for ISL while the other side is not.
D. ISL trunking requires that native VLANs match.
E. None of the other alternatives apply

最新試題

What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals?()

題型:單項選擇題

Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this?()

題型:單項選擇題

Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about the STP process for VLAN 200 are true? ()

題型:多項選擇題

Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()

題型:單項選擇題

During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()

題型:單項選擇題

Which three statements about STP timers are true?()

題型:多項選擇題

Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method?()

題型:單項選擇題

Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half  duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()

題型:單項選擇題

Refer to the exhibit. What does the command channel-group 1 mode desirable do? () 

題型:單項選擇題

DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()

題型:單項選擇題