Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.
Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）
A.R1 limi ts EIGRP to around 250Kbps on DLCI 102
B.R1 limits EIGRP to around 250Kbps on DLCI 104
C.R1 limits EIGRP to around 150Kbps on every DLCI
D.R1 does not limit EIGRP because noWAN bandwidth control has been configured
您可能感興趣的試卷
你可能感興趣的試題
A.Jitter
B.Delay
C.MTU
D.Reliability
A.By adding all subnets listed by the show ip route connected command
B.By adding the subnets of working interfaces over which static neighbors have been defined
C.By adding subnets redistributed on the local router from another routing source
D.By adding all subnets listed by the show ip route static command
An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（）
key chain fred
key 3
key - string whehew
interface fa0/0
ip authenticat ion key - chain eigrp 9 fred
A.The configuration is missing one authentication - related configuration command
B.The configuration is missing two authentication - related configuration commands
C.Authentication type 9 is not supported; type 5 should be u sed insteaD
D.The key numbers must begin with key 1, so change the key 3 command to key 1
A. The i nterface used by one router to connect to the other router is passive in the EIGRP process.
B. Duplicate EIGRP router IDs.
C. Mismatched Hold Timers.
D. IP addresses of 10.1.1.1/24 and 10.2.2.2/24, respectively.
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode.
Which of the following occurs？（）
A.Fa0/0 fails
B.The command is rejecteD
C.The existing three neighbors fail
D.The neighborship with 172.16.2.20 fails and then reestablishes
E.None of the other answers is correct
Routers R1 and R2, currently EIGRP neighbors over their Fa0/0 interfaces (respectively),both use EIGRP authentication. Tuesday at 8 p.m. the neighborship fails.
Which of the following wo uld not be useful when investigating whether authenticationhad anything to do with the failure？（）
A. debug eigrp packet
B. show key chain
C. show ip eigrp neighbor failure
D. show clock
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration.
Which of the following is true regarding the results from this c hange？（）
A.The show ip eigrp neighbors command on R1 lists the revised Hello timer
B.The show ip eigrp interfaces command on R1 lists the revised Hello timer
C.The R1 - R2 neighborship fails due to Hello timer mismatcH
D.The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2.
Which answer gives the reason for the omission？（）
A. R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.
B. S0/2 may currently be in a state other than up/up.
C. The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.
D. S0/2 may be configured as a passive inter face.
A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface.
Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）
A. 172.16.0.1/23
B. 172.16.1.1/26
C. 172.16.1.1/24
D. 172 .16.0.255/23
E. None of the other answers is correct.
Refer to the exhibit. Which two statements are true?（）
A. Router R1 will advertise connected and summary routes only.
B. The eigrp stub command will automatically enable summarization of routes on R2.
C. Router R1 is configured as a receive - only neighbor and will not send any connected, static, or summary routes.
D. The eigrp stub command prevents all routes except a default route from being advertised to R1.
E. The eigrp stub command prevents queries from being sent from R2 to R1.
F. Router R1 will advert ise connected and static routes. The sending of summary routes will not be permitted.
最新試題
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Which of the following are true of both OSPFv2 and OSPFv3?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）