Based on the show ip bgp summary output, which two statements are true?（）
A. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.
B. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.
C. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.
D. The BGP session to the 10.3.3.3 neighbor is established.
E. The BGP session to the 10.2.2.2 neighbor is established.
F. The BGP session to the 10.1.1.1 neighbor is established.
您可能感興趣的試卷
你可能感興趣的試題
A. An internal routing protocol can be used to reach an EBGP neighbor.
B. The next hop does not change when BGP updates are exchanged between EBGP neighbors.
C. EBGP requires a full mesh.
D. A static route can be used to form an adjacency between neighbors.
When an IPv6 enabled host boots, it sends a router solicitation (RS) message. An IPv6 router responds with a router advertisement (RA).
Which two items are c ontained in the RA?（）
A. any route advertisements it has received
B. prefixes for the link
C. keepalive timers
D. IPv6 address for the host
E. request for the local host IP address
F. lifetime of the prefix
A. They must be fully meshed
B. They can be in a different AS
C . They do not need to be directly connected
D. They must be directly connected
Refer to the exhibit diagram and config uration. RTB is summarizing its networks from AS 64100 with the aggregate - address command. However, the show ip route command on RTA reveals the RTB individual networks as well as its summary route.
Which option would ensure that only the summary route would appear in the routing table of RTA?（）
A. Add a static route with a prefix of 192.168.24.0 255.255.252.0 pointing to the null0 interface.
B. Create a route map permitting only the summary address.
C. Delete the four network statements and leave onl y the aggregate - address statement in the BGP configuration.
D. Add the keyword summary - only to the aggregate - address command.
Observe the diagram. RTC is the hub router and RTA and RTB are the spokes. There are no virtual circuits between the spoke locations. What is needed to successfully route traffic to the 11.11.11.0/24 network from RTA? （）
A. The neighbor 10.10.10.1 next - hop - self com mand on RTA
B. Nothing is required. This is the default behavior on this topology
C. The neighbor 10.10.10.1 next - hop - self command on RTB
D. The neighbor 10.10.10.1 next - hop - self command on RTC
A. weight
B. local preference
C. origin
D. AS_path
E. next hop
A. LOCAL_ PREF
B. AGGREG ATOR
C. AS_Path
D. Weight
A. weight
B. MED
C. local preference
D. origin
E. next - hop
F. AS - path
A. AS - path
B. next - hop
C. MED
D. weight
E. local preference
F. origin
The 192.168.0.0 network is not being propagated throughout the network. Observe the BGP configuration commands from the advertising router.
What is the reason the 192.168.0.0 route is not being advertised? （）
A. The network 192.168.0.0 statement is missing mask 255.255.0.0
B. The network 192.168.0.0 statement is missing mask 0.0.255.255.
C. The network 10.0.0.0 statement is missing mask 255 .0.0.0.
D. The network 10.0.0.0 statement is missing mask 0.255.255.255.
E. The auto - summary configuration is missing.
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64