HSRP has been configured between two Company devices.
What kind of message does an HSRP configured router send out every 3 seconds？（）
A. Retire
B. Coup
C. Resign
D. Send
E. Hello
您可能感興趣的試卷
你可能感興趣的試題
To protect against first-hop router failure， four protocols were developed to ensure IP routing redundancy.
Which of the following are they？（）
A. HSRP
B. IRDP
C. ICMP
D. VRRP
E. MSTP
F. GLBP
HSRP is being set up between two Company devices.
In what three states is it possible for an HSRP router to be in？（）
A. Standby
B. Established
C. Active
D. Idle
E. Backup
F. Init
R1 and R2 exchange HSRP between each other in the Company network.
In which three HSRP states do routers send hello messages？（）
A. Learn
B. Speak
C. Standby
D. Listen
E. Active
F. Remove
You need to implement a high availability design in the Company routed network.
Which protocol allows for the automatic selection and simultaneous use of multiple available gateways as well as automatic failover between those gateways？（）
A. VRRP
B. GLBP
C. IRDP
D. HSRP
E. None of the other alternatives apply
You need to decide on the best router redundancy protocol to use in the Company network.
Which two statements are true about HSRP， VRRP， and GLBP？（）
A. GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.
B. HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.
C. GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
D. Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.
E. GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure.
Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D. All routers configured for HSRP load balancing must be configured with the same priority.
E. Routers configured for HSRP must belong to only one group per HSRP interface.
You want to implement router redundancy in the Company network using the best method available.
Which protocol specified by RFC 2281 provides network redundancy for IP networks， ensuring that user traffic immediately and transparently recovers from first-hop failures in network edge devices or access circuits？（）
A. ICMP
B. IRDP
C. HSRP
D. STP
E. None of the other alternatives apply
pany uses GLBP to provide for router redundancy in the network.
Which describes the default load balancing scheme used by the Gateway Load Balancing Protocol （GLBP）？（）
A. Per host basis using a strict priority scheme
B. Per session using a round-robin scheme
C. Per session using a strict priority scheme
D. Per GLBP group using a strict priority scheme
E. Per host basis using a round-robin scheme
F. Per GLBP group using a round-robin scheme
HSRP has been configured between two Company devices.
Which of the following describe reasons for deploying HSRP？ （）
A. HSRP provides redundancy and fault tolerance
B. HSRP allows one router to automatically assume the function of the second router if the second router fails
C. HSRP allows one router to automatically assume the function of the second router if the second router starts
D. HSRP provides redundancy and load balancing
You want to implement a high availability network using two Cisco routers. You also want to ensure that the stat of the WAN interfaces can be tracked in doing so.
Which router redundancy protocol cannot be configured for interface tracking？ （）
A. GLBP
B. HSRP
C. RPR
D. VRRP
E. SLB
F. RPR+
G. None of the other alternatives apply
最新試題
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Which two statements are true when the extended system ID feature is enabled？ （）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）