A. Define the encapsulation type.
B. Define the standby router.
C. Define the standby IP address.
D. Enable the standby priority.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. HSRP has been configured and Link A is the primary route to router R4. When Link A fails， router R2 （Link B） becomes the active router.
Which router will assume the active role when Link A becomes operational again？" （）
A. The primary router R1 will reassume the active role when it comes back online.
B. The standby router R2 will remain active and will forward the active role to router R1 only in the event of its own failure.
C. The standby router R2 will remain active and will forward the active role to router R1 only in the event of Link B failure.
D. The third member of the HSRP group， router R3， will take over the active role only in event of router R2 failure.
Refer to the exhibit. The Gateway Load Balancing Protocol has been configured on routers R1 and R2， and hosts A and B have been configured as shown.
Which statement can be derived from the exhibit？（）
A. The hostA default gateway has been configured as 10.88.1.10/24.
B. The GLBP weighted load balancing mode has been configured.
C. The GLBP round-robin， load-balancing mode has been configured.
D. The GLBP host-dependent， load-balancing mode has been configured.
E. The hostA default gateway has been configured as 10.88.1.1/24.
F. The hostA default gateway has been configured as 10.88.1.4/24.
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails？（）
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
Routers can send hello messages in three HSRP states.
Which ones are they？（）
A. Standby
B. Learn
C. Listen
D. Speak
E. Active
Router R1 is configured for HSRP.
Which of the following are valid HSRP states on R1？ （）
A. Init
B. Idle
C. Active
D. Standby
E. Established
F. Backup
You have configured router R1 with HSRP， using the standard defaults.
Which three statements are true of a default HSRP configuration？（）
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.
You need to design router redundancy on the Company network.
Which three protocols could be chosen for IP routing redundancy to protect against first-hop router failure？（）
A. GLBP
B. ICMP
C. MSTP
D. HSRP
E. VRRP
F. NHRP
Router R1 and R2 are both configured for HSRP.
Which two statements about the HSRP priorities of these two routers are true？（）
A. To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.
B. The default priority of a router is zero （0）.
C. The no standby priority command assigns a priority of 100 to the router.
D. Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.
E. When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
Which first-hop redundancy solution listed would supply Company clients with MAC address0000.0C07.AC0A for group 10 in response to an ARP request for a default gateway？（）
A. IRDP
B. Proxy ARP
C. GLBP
D. HSRP
E. VRRP
F. IP Redirects
You work as a network technician at Company. Your boss， Mrs. ， is interested in
GLBP. In particular， she wants to know the multicast address that this protocol uses.
What should you tell her？ （）
A. 224.0.0.100
B. 224.0.0.1
C. 224.0.0.102
D. 224.0.0.10
E. 224.0.0.101
F. None of the other alternatives apply
最新試題
Which two statements are true when the extended system ID feature is enabled？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Which two statements about the various implementations of STP are true？（）