A. RIP
B. BGP
C. IS - IS
D. OSPF
E. EIGRP
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）
A. The redistribution command should be reentered with the match route - type parameter included.
B. The redistribution command should be reentered wit h the route - map map - tag parameter included.
C. The redistribution command should be reentered with the metric metric - value parameter included.
D. Routes will first need to be distributed into another protocol, and then into RIP.
Refer to the exhibit. What is required to complete the IPv6 routing configurations shown?（）
A. Interface authentication must be configured
B. The routing processes must be configured with an area ID
C. IP unicast routing must be enabled
D. IPv4 ad dresses must be applied to the interfaces
Refer to the parti al configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?（）
A. the serial 1/1 address
B. the serial 2/0 address
C. a randomly generated internal address
D. the configured router - id address
A.Interfaces have a default metric of 1.
B.Level 1 is intra - area and level 2 is interarea.
C.Level 1 routing is between an end system (ES) and IS while Level 2 routing is between an IS and IS.
D. Hosts send ISHs while routers send ESHs.
E. IS - IS is an open standard.
F. Metrics depend on interface speed.
Intermediate system to intermediate system (IS - IS), is a protocol used by network devices (routers) to determine the best way to forward datagrams through a packet - switched network, a process called routing. Which three attributes are of the IS - IS routing protocol? （）
A. supports VLSM
B. link - state routing protocol
C. operati on is similar to BGP
D. supports two routing levels within an autonomous system
Refer to the exhibit. Which two statements are true?（）
A. DHCPDISCOVER packets will reach the DHCP server.
B. The router will not forward DHCPDIS COVER packets because it has not been configured to do so.
C. This configuration is applied to interface Fa0/1.
D. DHCPDISCOVER packets will not reach the DHCP server because DHCPDISCOVER packets are broadcasts.
E. DHCPDISCOVER packets will not reach the DHCP server because ports 67 and 68 have not been explicitly allowed by the ip forward - protocol command.
F. This configuration is applied to interface Fa0/0.
A. when all equipment is manufactured by Cisco
B. when there are multiple paths to destination networks
C. because having multiple routing protocols confuses hackers
D. when migrating from an older Interior Gateway Protocol (IGP) to a new IGP
E. when using UNIX host - based routers
F. when smaller broadcast domains are desired
A. The multicast sources must register with the RP to form the multicast distribution tree.
B. An RP is required only in networks running Protocol Independent Multicast dense mode (PIM DM).
C. The mu lticast receivers must register with the RP to form the multicast distribution tree.
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM).
E. An RP is required only in networks running Protocol Independent Mu lticast sparse - dense mode (PIM - SDM).
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP.
Refer to the exhibit. Based upon the information in the exhibit, which statement is true?（）
A. DHCP requests from the host will be rebroadcasted to R2.
B. To complete t his configuration, the R1 fa0/0 interface must be configured with the ip helper - addresses command.
C. To complete this configuration, the R2 fa0/0 interface must be configured with the ip helper -addresses command.
D. R1 will forward all DHCP requests t o both 192.168.100.1 and 192.168.200.1 as unicast messages.
E. R1 will forward DHCP requests to 192.168.100.1. If there is no response, R1 will then forward the requests to 192.168.200.1.
Refer to the exhibit. Which configuration would correctly enable Host A to acquire an IP address from the DHCP server that is located at 10.1.2.10/24? （）
A.ASw1(config)# interface range FastEthernet 0/1 - 24 ASw1(config - if - range)# ip forward - protocol udp 67 ASw1(config - if - range)# ip forward - protocol udp 68
B.ASw1(config)# interface range FastEthernet 0/1 - 24 ASw1(config - if - range)# ip helper - address 10.1.2.10
C.RTA(config)# interface fastethernet0/0 RTA(config -if)# ip forward- protocol udp 67 RTA(config - if)# ip forwar d- protocol udp 68
D.RTA(config)# interface fastethernet0/1 RTA(config -if)# ip forward- protocol udp 67 RTA(config -if)# ip forward- protocol udp 68
E.RTA(config)# interface fastethernet0/0 RTA(config - if)# ip helper - address 10.1.2.10
F.RTA(config)# in terface fastethernet0/1 RTA(config - if)# ip helper - address 10.1.2.10
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Which of the following are true of both OSPFv2 and OSPFv3?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）