Refer to the exhibit. A company would prefer all Internet - bound OSPF routed traffic to use ISP ABC with ISP DEF as a backup. As the network consultant, what three configuration changes might you make?（）
A. The default -information originate command should be configured on router B1 and B4.
B. The default -information originate command should be configured on router B2 and B3.
C. If the metric value for ISP ABC is set at the default, the I SP DEF metric value should be set to 1.
D. If the metric value for ISP ABC is set at the default, the ISP DEF metric value should be set to 25.
E. The metric type value should be set to type 1.
F. The metric type value should be set to type 2.
您可能感興趣的試卷
你可能感興趣的試題
A. Autoconfiguration
B. Automatic 6to4 Tunnel
C. Automatic 6to4 Relay
D. Network Address Translator - Protocol Translator (NAT - PT)
E. Intrasite Automatic T unnel Address Protocol (ISATAP)
A. soft - reconfiguration
B. route refresh
C. BGP communities
D. full - mesh BGP peering
A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers
Refer to the above exhibit. Why are the EIGRP neighbors for this router not learning the routes redistributed from OSPF?（）
A. Redistribution must be enabled mutually (in both directions) to work correctly.
B. auto - summary causes the OSPF routes redistributed into EIGRP to be summarized; thus the OSPF network 116.16.34 is summarized to 116.3 4.0.0, which is already covered by the EIGRP protocol.
C. Default metrics are not configured under EIGRP.
D. Both routing protocols must have unique autonomous system numbers for redistribution to function correctly.
Refer to the above exhibit. Why is the 140.140.0.0 network not used as the gateway of last resort even though it is configured first?（）
A.The last default - network statement will always be preferred.
B.A route to the 140.140.0.0 network does not exist in the routing table.
C.Default - network selection will always prefer the statement with the lowest IP address.
D.A router will load balance across multiple default - networks; repeatedly issuing the show ip route command would show the gateway of last resort changing between the two networks.
A. EIGRP would be appropriate if LMI type ANS I is NOT used.
B. EIGRP would be appropriate, because the Frame Relay spokes could be segmented into their own areas.
C. EIGRP would be appropriate, because by default, queries are not propagated across the slow speed Frame Relay links.
D. EIGRP would be appropriate, because you can manage how much bandwidth is consumed over the Frame Relay interface.
A. A change in the load on an interface will cause EIGRP to recalculate the routing metrics and send a corresponding update out to each of its neighbors.
B. EIGRP calculates interface load as a 5 - minute exponentially weighted average that is updated every 5 minutes.
C. EIGRP considers the load of an interface only when sending an update for some other reason.
D. A change in the load on an interface will cause EIGRP to recalculate and update the administrative distance for all routes learne d on that interface.
Based on the need to limit processing and bandwidth utilization due to dynamic routing protocol operation, the foll owing routing requirements have been specified for your network.
- partial and incremental routing updates
- only the devices affected by a topology change perform route recomputation
- route recomputation only occurs for routes that were affected
Which dynamic routing protocol should be deployed in your network to best meet these requirements?（）
A. BGP
B. OSPF
C. IS - IS
D. EIGRP
E. RIPv2
A. The neighbor's advertised distance must be less than or equal to the feasible distance of the current successor.
B. The neighbor's advertised distance must be less than the f easible distance of the current successor.
C. The neighbor's advertised distance must be greater than the feasible distance of the current successor.
D. The neighbor's advertised distance must be equal to the feasible distance of the current successor .
E. The neighbor's advertised distance must be greater than or equal to the feasible distance of the current successor.
A. Internal routers within the backbone area (area 0)
B. Internal routers within the NSSAs
C. Internal routers within the stubby areas
D. ASBRs
E. ABRs
F. DRs and BDRs
最新試題
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）