A.Switch（config-if）#spanning-tree guard root
B.Switch（config-if）#spanning-tree portfast
C.Switch（config-if）#switchport mode trunk
D.Switch（config-if）#switchport mode access
您可能感興趣的試卷
你可能感興趣的試題
A port in a redundant topology is currently in the blocking state and is not receiving BPDUs. To ensure that this port does not erroneously transition to the forwarding state，
which command should be configured to satisfy the requirement？（）
A.Switch（config）#spanning-tree loopguard default
B.Switch（config-if）#spanning-tree bdpufilter
C.Switch（config）#udld aggressive
D.Switch（config-if）#spanning-tree bpduguard
A.spanning-tree guard root
B.spanning-tree portfast bpduguard default
C.spanning-tree bpduguard enable
D.spanning-tree bpdufilter enable
E.spanning-tree portfast bpdufilter default
A.a native VLAN mismatch on either side of an 802.1Q link
B.BPDU filter configured on a link to another switch
C.Spanning Tree Protocol enabled on both Layer 2 and multilayer switches
D.PortFast enabled on all access and trunk ports
A.Configuration changes made on the port-channel interface apply to all physical ports assigned to the portchannel interface.
B.Configuration changes made on a physical port that is a member of a port-channel interface apply to the port-channel interface.
C.Configuration changes are not permitted with Port Aggregation Protocol； instead， the standardized Link Aggregation Control Protocol should be used if configuration changes are required.
D.The physical port must first be disassociated from the port-channel interface before any configuration changes can be made.
A.no switchport trunk native vlan vlan-id
B.switchport nonegotiate
C.no switchport mode dynamic desirable
D.switchport mode access
A.switchport dynamic auto switchport dynamic auto
B.switchport access vlan 10 switchport mode dynamic desireable
C.switchport mode trunk switchport nonegotiate
D.Leave both ports with the default trunk settings
A.By default， native VLAN packets going out this port will be tagged.
B.Without an encapsulation command， 802.1Q will be the default encapsulation if DTP fails to negotiate a trunking protocol.
C.The interface will support the reception of tagged and untagged traffic.
D.If the device connected to this port is not 802.1Q-enabled， it will not be able to handle 802.1Q packets.
A.PortFast， UplinkFast， and BackboneFast specific configurations are ignored in Rapid PVST mode.
B.RSTP is enabled globally and uses existing STP configuration.
C.Root and alternative ports transition immediately to the forwarding state.
D.Convergence is improved by using sub-second timers for the blocking， listening， learning， and forwarding port states.
A.Unidirectional link detection is achieved through monitoring STP BPDUs.
B.It is recommended that it be enabled globally rather than on an individual port.
C.When an error is detected， normal mode will disable a port.
D.It is recommended that it be enabled in normal mode.
E.It is recommended that it be used with the loop guard feature.
A.Upon startup， the port transmits 10 BPDUs. If the port receives a BPDU， PortFast and BPDU guard are disabled on that port and it assumes normal STP operation.
B.The access port ignores any received BPDU.
C.If the port receives a BPDU， it is placed into the error-disable state.
D.BPDU guard is only configured globally and the BPDU filter is required for port-level configuration.
最新試題
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Which three statements about STP timers are true？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）