A. When a router receives a failure response, it stops querying authentication methods.
B. When a router receives an error response, it stops querying authentication methods.
C. If the router receives a failure response from an authentication method, it queries the next method.
D. The router does not differentiate between failure and error responses; the authentication process is always interrupted.
E. If it receives no response from the authentication method, a router will determine the error condition On its own; the router also has the option to proceed to the next method in a list if configured accordingly.
您可能感興趣的試卷
你可能感興趣的試題
A. A pointer to the address where a RADIUS server can be located
B. A sequential list of user authentication methods
C. A description of what a user can execute on a router
D. The setup for the authentication phase on a router
A. Apply the method list to an interface
B. Specify the default method list and apply it to the interface
C. Enable AAA
D. Define a method list
A. policy map
B. class map
C. ACL
D. service policy
A. Protocol and IP source only
B. IP Source, IP Destination and ports
C. IP Source Only
D. IP Destination Only
A Cisco Catalyst switch is part of the CIS network. As an experienced network administrator, you are thinking of filtering the traffic within VLANI00 with the use of a VACL named "test" on that switch.
Which of the following command will enable that?（）
A. interface vlan 100 ip access-group test in
B. interface vlan 100 ip access-group test
C. vlan access-map test 100
D. vlan filter test vlan-list 100
A. Information about port roles is sent to all switches.
B. RSTPs that are based on Cisco products require no additional configuration.
C. Features such as UplinkFast and BackboneFast are compatible with RSTP.
D. An RSTP that is based on Cisco products generally performs better than the Cisco proprietary 802.1D enhancements.
A.ISSU，OSPF，IS-IS
B.IETF，OSPF，ISSU
C.IS-IS，EIGRP，SSO，BGP
D.EIGRP，BGP，OSPF，IS-IS
A. Automatic switchover from active to standby on primary supervisor failure
B. Reset of the primary supervisor.
C. Manual switchover from active to standby supervisor
D. Manual switchover from standby to active supervisor
A. show redundancy states, redundancy, mode sso
B. show redundancy states, mode sso, redundancy
C. redundancy, mode sso, show redundancy states
D. mode sso, redundancy, show redundancy states
A.RPR
B.BGP
C.SSO
D.SRM
最新試題
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）
What are four advantages to using tunnel brokers in an IPv6 transition environment?（）
You are an experienced network administrator in an international corporation. During your working hours, you are asked to deploy the Cisco SSL VPN AIM module in a Cisco 1800 Series Router. The beneficial reason for that deployment is to:（）
You are an experienced network administrator in an international corporation. One of your clients asks you to configure a network for a financial trading center which requires multiple high-value transactions.And the transactions are very important to the client. In such a situation, which two of the following are basic and most important requirements concerning the configuration? （）(Choose two.)
What is the maximum number of Cisco Catalyst 3750 Series Switches that can be united into a single manageable unit using the Cisco StackWise technology?（）
Which command displays only those entries in a BGP table with specific AS_PATH attributes?（）
In a RSTP implementation, which of the following two link types are used? （）(Choose two.)
Refer to the exhibit. Which SSH sessions will the SSH server accept?（）
Which Cisco IOS command is used to troubleshoot a problem in which a BGP session stays in the active state?（）
Refer to the exhibit. For the given configuration, on packets leaving the router on interface FastEthernet0/0 that matches the high traffic class, what will the MPLS experimental bit be set to?（）