On a Cisco Aironet 1130AG Series standalone access point， the status LED is dark blue andblinking.
What does this indicate？（）
A.The internal radio has failed.
B.A firmware upgrade is in progress.
C.An access point buffer overflow is occurring.
D.The access point is booting.
您可能感興趣的試卷
你可能感興趣的試題
In a deployment using standalone access points， clients set up to authenticate with EAP-PEAP orEAP-Cisco Wireless （Cisco-LEAP） cannot authenticate. When you inspect the Failed Attemptsreport on the Cisco Secure ACS，you find this error："Unknown network access server NAS."
Which problemmayhave caused this failure？（）
A.misconfigured IP address of the AAA server on the access point
B.misconfigured EAP type on the access point
C.misconfigured IP address of the access point on the AAA server
D.misconfigured EAP type on the AAA server
A.router（config-ssid）# guest-mode
B.router（config-ssid）# advertise
C.router（config-ssid）# enable
D.router（config-ssid）# broadcast
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID tag data is not being collected.
On which device would you verify that RFIDs have been enabled？（）
A.access point
B.location manager
C.wireless controller
D.Cisco WCS
A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
A.five
B.three
C.six
D.four
A.Cisco-LEAP， EAP-FAST， EAP-PEAP （GTC）， EAP-TLS
B.Cisco-LEAP， EAP-PSK， EAP-PEAP （MS-CHAP v2）， EAP-TLS
C.Cisco-LEAP， EAP-FAST， EAP-PEAP （MS-CHAP v2）， EAP-TTLS
D.Cisco-LEAP， EAP-MD5， EAP-PEAP （GTC）， EAP-TTLS
You are using standalone Cisco Aironet 1400 Series Wireless Bridges for a nine-mile point-to-point wireless link between two buildings.
Which distance setting should you use for the bridgeconfigured as the root？（）
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
A.enable concatenation on the non-root bridge only
B.enable concatenation on the root bridge only
C.enable concatenation on both the root bridge and non-root bridge
D.enable concatenation on the root bridge and set it as desirable on the non-root bridge
E.set concatenation as desirable on the root bridge and enable it on the non-root bridge
EAP-FAST provides a secure tunnel during Phase One to protect the user’s authenticationcredentials.
Which of these entities initializes the secure tunnel？（）
A.x.509 certificate
B.generic token card
C.preshared key
D.Protected Access Credential
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID beacon rate is 10 seconds and you have discovered an issue with the RFID timeoutvalue.
Where and how should the RFID value be changed？（）
A.on the Cisco WCS， to 95 seconds
B.on the wireless controller， to 45 seconds
C.on the wireless controller， to 95 seconds
D.on the Cisco WCS， to 45 seconds
最新試題
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）