You are installing a Cisco 4402 Series Wireless LAN Controller.
Which type of interface should you use onthe controller’s distribution port？（）
A.10/100 Mbps RJ45
B.1000BASE-SX SFP
C.10/100/1000 Mbps RJ45
D.10000BASE-SX
您可能感興趣的試卷
你可能感興趣的試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The
phone rings but， when you answer， the call is dropped.
What may have caused this problem？（）
A.Publicly Secure Packet forwarding is enabled.
B.The minimum data rate is not set to 11 Mbps.
C.An address resolution protocol is enabled.
D.The access point is set to the least congested channel.
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor， 4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the network andis being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of them are beingtracked on the Cisco WCS.
What can be done to correct the problem？（）
A.Add a new location appliance.
B.Add a new Cisco WCS server dedicated to the location appliance.
C.Add 4 GB of RAM to the Cisco WCS.
D.Add a 120 GB hard drive to the Cisco WCS.
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be a roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserved for roaming on the WLAN controller tothe maximum.
What level do you set the bandwidth to？（）
A.25 percent
B.15 percent
C.5 percent
D.35 percent
Using the WLSE， you are trying to push out a configuration job to a standalone access point， butthe job does not start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.pop-up blocker enabled in the browser
D.unsupported version of IOS firmware in the access point
A.50
B.128
C.512
D.1024
A.128
B.32
C.16
D.64
A.12 percent
B.6 percent
C.18 percent
D.24 percent
A.16 feet [4.8 meters]
B.24 feet [7.3 meters]
C.8 feet [2.4 meters]
D.40 feet [12.1 meters]
You are using ADU and are authenticated and associated to an access point. However，you areunable to obtain an IP address.
Which of these has caused this problem？（）
A.invalid SSID
B.invalid WEP key
C.invalid encryption type
D.invalid 802.1X authentication type
最新試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）