On a Series 1010 lightweight access point， the alarm LED is flashing red， and all other LEDs are off.
What is the lightweight access point indicating？（）
A.It has lost contact with controller.
B.Its IP address already exists.
C.It requires a code upgrade.
D.It is operating normally.
您可能感興趣的試卷
你可能感興趣的試題
A.router# show wlccp ap
B.router# show wlccp wds ap
C.router# show wlccp cckm
D.router# show wlccp wds cckm
A.HTTPS
B.TFTP
C.RMI
D.HTTP
E.FTP
A.SSIDs are not case sensitive.
B.SSIDs must be listed in the same order in the ADU as they are in the access point.
C.A maximum of three SSIDs may be configured.
D.SSIDs may have a maximum of 16 characters.
Using the WLSE，you are trying to push out a configuration job to an access point，but the job doesnot start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.unsupported version of IOS firmware in the access point
D.pop-up blocker enabled in the browser
A.75
B.100
C.25
D.50
Client association using EAP-Cisco Wireless （LEAP） is failing， but EAP-PEAP is functioning on an autonomous access point.
Which of the following needs to be enabled on the access point so EAP-Cisco Wireless （LEAP） is enabled？（）
A.open authentication plus MAC
B.open authentication plus EAP
C.shared key
D.network EAP
A.Devices
B.IDS
C.Configure
D.Reports
A.1813
B.1645
C.1646
D.1812
A.chooses the least congested channel
B.uses the configured channel
C.sets all access points to the same channel
D.steps through each of the allowed channels
A.EAP-FAST master server
B.Allow automatic PAC provisioning
C.client initial message
D.authority ID info
最新試題
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）