A.Establish a direct link from the switch to all other switches in the network.
B.Assign the switch a higher MAC address than the other switches in the network have.
C.Configure the switch so that it has a lower priority than other switches in the network.
D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.
E.Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.

A.發送一個單播ARP包到DSL調制解調器/路由器
B.發送一個單播ICMP包到DSL調制解調器/路由器
C.發送三層廣播包到響應的DSL調制解調器/路由器
D.發送一個可以被Host2，the switch，and the DSL modem/router 受到的2層廣播幀

A.Convert all the routers to EIGRP and use 198.133.219.32/27, 198.133.219.64/27, and 198.133.219.92/27 as the new subnetworks.
B.Maintain the use of RIP version 1 and use 198.133.219.32/27, 198.133.219.64/27, and 133.219.92/27 as the new subnetworks.
C.Convert all the routers to EIGRP and use 198.133.219.64/26, 198.133.219.128/26, and 133.219.192/26 as the new subnetworks.
D.Convert all the routers to RIP version 2 and use 198.133.219.64/26, 198.133.219.128/26, and 133.219.192/26 as the new subnetworks.
E.Convert all the routers to OSPF and use 198.133.219.16/28, 198.133.219.32/28, and 198.133.219.48/28 as the new subnetworks.
F.Convert all the routers to static routes and use 198.133.219.16/28, 198.133.219.32/28, and

A.show session
B.show cdp neighbors
C.show users
D.show queue

A.It is used to validate the sources of VTP advertisements sent between switches.
B.It is used to access the VTP server to make changes to the VTP configuration.
C.It allows two VTP servers to exist in the same domain, each configured with different passwords.
D.It is the password required when promoting a switch from VTP client mode to VTP server mode.
E.It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.

A.to provide routing to a local web server
B.to provide routing from an ISP to a stub network
C.to provide routing that will override the configured dynamic routing protocol
D.to provide routing to a destination that is not specified in the routing table and which is outside the local network

A.to verify the type of cable interconnecting two devices
B.to determine the status of network services on a remote device
C.to obtain VLAN information from directly connected switches
D.to verify Layer 2 connectivity between two devices when Layer 3 fails
E.to obtain the IP address of a connected device in order to telnet to the device
F.to determine the status of the routing protocols between directly connected routers

A.Passive routes are in the process of being calculated by DUAL.
B.EIGRP supports VLSM, route summarization, and routing update authentication.
C.EIGRP exchanges full routing table information with neighboring routers with every update.
D.If the feasible successor has a higher advertised distance than the successor route, it becomes the primary route.
E.A query process is used to discover a replacement for a failed route if a feasible successor is not identified from the current routing information.

A.Broadcasts only use network layer addressing.
B.A broadcast frame is never forwarded by a switch.
C.A broadcast address will never be the source address of a frame.
D.Broadcast addresses use an incorrect format for the switching table.
E.Broadcast frames are never sent to switches.

A.transport type all
B.transport output all
C.transport preferred all
D.transport input all