A.Make sure that the server can be reached across the network.
B.Check that authentication for TFTP access to the server is set.
C.Assure that the network server has adequate space for the IOS image.
D.Verify file naming and path requirements.
E.Make sure that the server can store binary files.
F.Adjust the TCP window size to speed up the transfer.
您可能感興趣的試卷
你可能感興趣的試題
A.Replace the straight-through cable with a crossover cable
B.Change the subnet mask of the hosts to /25
C.Change the subnet mask of the hosts to /26
D.Change the address of Workstation A to 192.0.2.15
E.Change the address of Workstation B to 192.0.2.111
A.Switch1(config-if)# switchport port-security maximum 1
B.Switch1(config)# mac-address-table secure
C.Switch1(config)# access-list 10 permit ip host
D.Switch1(config-if)# switchport port-security violation shutdown
E.Switch1(config-if)# ip access-group 10
A.copier
B.microwave oven
C.toaster
D.cordless phone
E.IP phone
F.AM radio
A.Switch1 - Fa 0/2
B.Switch1 - Fa 0/9
C.Switch2 - Fa 0/3
D.Switch2 - Fa 0/4
E.Switch2 - Fa 0/8
F.Router - Fa 1/0
A.If RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.
B.If RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.
C.If EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.
D.If EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.
E.If EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.
F.If EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.
A.addresses chosen by a company to communicate with the Internet
B.addresses that cannot be routed through the public Internet
C.addresses that can be routed through the public Internet
D.a scheme to conserve public addresses
E.addresses licensed to enterprises or ISPs by an Internet registry organization
A.VTP
B.STP
C.ISL
D.802.1Q
E.VLSM
A.buffering
B.cut-through
C.windowing
D.congestion avoidance
E.load balancing
A.Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interface
B.Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic
C.Configure many sub-interfaces on the same subnet
D.Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
Which routing protocols will support the following IP addressing scheme? （）
Network 1 - 192.168.10.0 /26
Network 2 - 192.168.10.64 /27
Network 3 - 192.168.10.96 /27
Network 4 - 192.168.10.128 /30
Network 5 - 192.168.10.132 /30
A.RIP version 1
B.RIP version 2
C.IGRP
D.EIGRP
E.OSPF
最新試題
在路由器上使用Router#copy running-config startup-config 命令會產生什么效果？（）
請參見圖示。一臺路由器（其路由表如圖所示）收到發往192.168.1.4的數據包。路由器將如何處理該數據包？（）
請參見圖示。主機A 嘗試與主機C 建立TCP/IP 會話。在嘗試期間，路由器Y 的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為172.16.1.5而目的IP 地址為172.16.7.24的數據包。捕獲該幀時，它的源MAC 地址是什么？（）
在Cisco IOS 設備中，啟動配置文件存儲于何處？（）
傳輸層如何讓主機能同時針對不同應用程序維護多個通信流？（）
請參見圖示。主機B 嘗試與主機C 建立TCP/IP 會話。在嘗試期間，San Francisco 器由器的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為10.10.1.2而目的IP 地址為10.31.1.20的數據包。捕獲該幀時，它的目的MAC 地址是什么？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€(gè)邏輯地址范圍？（）
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是，從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題？（）
何時必須使用clock rate 命令配置路由器串行接口？（）
請參見圖示。公司路由器由于故障被更換。更換路由器之后，Education 辦公室內的主機C 和D 能夠相互ping 通，但是無法訪問Accounts 辦公室內的主機。此問題的原因可能是什么？（）