A. Cisco NX-OS Software does not support PIM dense mode.
B. The command ip multicast-routing must be enabled in Cisco NX-OS Software before any multicast configuration is possible on the switch.
C. PIM CLI configuration and verification commands are not available until you enable the PIM feature with the feature pim command.
D. Cisco NX-OS Software supports multicast routing per Layer 3 VRF instance.
E. The default PIM operational mode on the Cisco Nexus 7000 switch is SSM.
您可能感興趣的試卷
你可能感興趣的試題
A. The L2 multicast frames are encapsulated in an OTV packet using the configured control-group multicast address for transport
B. The L2 multicast frames are dropped because multicast cannot be carried across the overlay
C. The L2 multicast frames are encapsulated in an OTV packet using the configured data-group multicast address for transport
D. The L2 multicast frames are forwarded natively across the overlay based on their multicast IDs
A. 128
B. 32
C. 64
D. Dependent on the number of switch IDs in the topology
A. IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.
B. The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.
C. IGMP snooping has been disabled on the VLAN 120 SVI.
D. IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.
E. IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
Nexus# sh ip igmp snooping vlan 120
IGMP Snooping information for vlan 120
IGMP snooping disabled
Optimised Multicast Flood （OMF） disabled
IGMP querier none
Switch-querier enabled， address 1.1.1.1， currently not running
IGMPv3 Explicit tracking enabled
IGMPv2 Fast leave disabled
IGMPv1/v2 Report suppression enabled
IGMPv3 Report suppression disabled
Link Local Groups suppression enabled
Router port detection using PIM Hellos， IGMP Queries
Number of router-ports： 0
Number of groups： 0
Active ports： Po100 Po111
Which statement best describes what is depicted in the show command output？（）
A. IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.
B. The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.
C. IGMP snooping has been disabled on the VLAN 120 SVI.
D. IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.
E. IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
A. Synchronizes ARP entries between vPC peers every five minutes
B. Triggers a manual update of ARP entries from the primary peer to the secondary
C. Enables a bulk loading of ARP entries when a vPC peer is restored
D. Uses the peer-keepalive link to maintain ARP table consistency
A. admin， operator， network-admin， and network-operator
B. admin， read-only， network-admin， and network-operator
C. vdc-admin， vdc-operator， network-admin， and network-operator
D. vdc-admin， vdc-operator， network-admin， and network-operator （for Nexus 7000） and network- admin and network-operator （for other Nexus switches）
E. admin and read-only
A. IGMP is not synchronized between vPC peers
B. Cisco Fabric Service carries IGMP entries across the vPC peer link
C. IP ARP synchronization under the vPC domain configuration also synchronizes IGMP
D. IGMP is flooded to the L2 domain， and there is no need to synchronize it between vPC peers
A. The OTV control-plane protocol uses the IS-IS protocol to establish adjacencies and exchange MAC reachability across the overlay network. You must enable IS-IS with the feature isis command before OTV adjacencies can be established.
B. OTV uses an SSM group range for neighbor discovery and to exchange MAC reachability with other OTV edge peers.
C. The OTV join interface is a routed uplink interface on the edge device used to physically join the overlay network.
D. The OTV internal interface encapsulates the site Layer 2 frames in IP unicast or multicast packets that are then sent to the other sites.
A. C84C·75FA·6000
B. 01005·E11.·2FD
C. C84C·76FA·6000
D. 4000.0000.0001
A.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config delete-config and edit-config
B.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config edit-config and kill-session
C.NX-OS Software supports up to a maximum of 16 concurrent XML sessions
D.Only show commands are supported via the XML management interface in NX-OS Software
E.The NX-OS implementation of the XML-based NETCONF requires SSH to be used for communication with the device
最新試題
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS？（）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
An administrator is creating a service profile but receives an error when applying to a blade. The administrator checks the faults tab of the service profile and finds the following error （Refer to the exhibit）.What is the cause of this error？（）
Which statement is true regarding Backup tasks in Cisco UCS？（）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）
Where are SAN Port Channel is created in UCS Manager？（）
When testing ICMP access to a functional load-balancing ACE VIP， it fails. What is the reason of this problem？ （）