A. They are created automatically and stored on the FI
B. They are created manually and exported to a remote server
C. They are automatically scheduled to run every 24 hours
D. They are manually scheduled and stored on the FI
您可能感興趣的試卷
你可能感興趣的試題
A. During the initial configuration from the console
B. Once the basic configuration has been applied
C. To restore the configuration on a secondary fabric interconnect
D. To upgrade the firmware on a replacement fabric interconnect
A. Only to Cisco Fibre Channel switches
B. Only to Cisco Fibre Channel switches in NPIV mode
C. To any Fibre Channel switch
D. Directly to storage arrays
E. Only to Nexus Switches
A. Under the Admin tab on the FI
B. Under the Server tab in the service profile
C. Under the SAN tab on each VSAN
D. Under the Admin tab on the chassis
E. Under the SAN tab on the Fabric Interconnect
Given the following output：
san-port-channel 12 is up
Hardware is Fibre Channel
Port WWN is 24：0c：00：0d：ec：d3：5c：00
Admin port mode is NP， trunk mode is on
Port mode is NP Port vsan is 1
Speed is 8 Gbps
Member[1] ： fc2/3
Member[2] ： fc2/4
What does "Speed is 8 Gbps" indicate？（）
A. The speed of the slowest interface in the port channel
B. The combined speed of all interfaces configured in the port channel
C. The combined speed of all interfaces in the port channel that are up
D. The speed that can be achieved if all buffers are used
A. Server
B. End device
C. Node
D. Host
E. Virtual
A. Sending all broadcasts
B. Receiving all traffic from upstream switches
C. Receiving broadcast traffic
D. Negotiating spanning tree with upstream switches
E. Learning MAC addresses from upstream switches
A. The Cisco VIC can create an unlimited number of Virtual NICs
B. The number of vNICs on the Cisco VIC that can be created is determined by the number of chassis uplinks
C. vNICs are created using software on the host operating system
D. The host operating system sees a vNIC as a physical PCIe device
E. The host operating system sees a vNIC as a sub-interface of a primary NIC
F. The Cisco VIC can create 1024 vNICs
A. Fibre Channel storage
B. UCS C-Series servers
C. NFS storage
D. UCS chassis
E. Other fabric interconnect
A. End-host mode is synonymous with NPV mode.
B. In end-host mode， only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.
C. Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.
D. End-host mode is the default Fibre Channel switching mode.
A. In the blade BIOS
B. In the operating system
C. In the service profile
D. In the card option ROM
最新試題
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
Which statement is true regarding Backup tasks in Cisco UCS？（）
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true？ （）
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）
In the event of a GSS failure in a GSS cluster， which is true？（）
KAL-AP on the Cisco ACE allows communication with Cisco ACE Global Site Selector， to report virtual IP and real server availability. Which statement is true about KAL-AP？（）
What is the purpose of this command in a Cisco Application Control Engine？（） switch/Admin# show np 1 me-stats "-F0 v"
An administrator is creating a service profile but receives an error when applying to a blade. The administrator checks the faults tab of the service profile and finds the following error （Refer to the exhibit）.What is the cause of this error？（）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）