A network administrator is troubleshooting the OSPF configuration of routers R1 and R2.The routers cannot establish an adjacency relationship on their common Ethernet link.The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.Based on the information in the graphic,what is the cause of this problem?（）
A.The OSPF area is not configured properly.
B.The priority on R1 should be set higher.
C.The cost on R1 should be set higher.
D.The hello and dead timers are not configured properly.
E.A backup designated router needs to be added to the network.
F.The OSPF process ID numbers must match.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.The network administrator is in acampus building distant from Building B.WANRouter is hosting a newly installed WAN link on interface S0/0.The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface.How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner?（）
A.Telnet to WANRouter and execute the command show interfaces S0/0
B.Telnet to WANRouter and execute the commandshow processes S0/0
C.Telnet to WANRouter and execute the command show running-configuration
D.Telnet to WANRouter and execute the command show controller S0/0
E.Physically examine the cable between WANRouter S0/0 and the DCE.
F.Establish a console sessionon WANRouter and execute the command show interfaces S0/0
Refer to the exhibit.How many broadcast domains exist in theexhibited topology？（）
A.one
B.two
C.three
D.four
E.five
F.six
A.24
B.4
C.3
D.16
The Frame Relay network in the diagram is not functioning properly.What is the cause of the problem?（）
A.The Gallant router has the wrong LMI type configured
B.Inverse ARP is providing the wrong PVC information to the Gallant router
C.The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D.The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E.The IP address on the serial interface of the Attalla router is configured incorrectly
A.Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interface
B.Configure each Frame Relay circuit as apoint-to-point line to support multicast and broadcast traffic
C.Configure many sub-interfaces on the same subnet
D.Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
A.A CSU/DSU terminates a digital local loop
B.A modem terminates a digital local loop
C.A CSU/DSU terminates an analog local loop
D.A modem terminates an analog local loop
E.A router is commonly consideredaDTEdevice
F.A router is commonly considereda DCE device
Refer to the exhibit.What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown？（）
A.The Seria l0/0interface is passing traffic.
B.The DLCI 100 was dynamic allyallocated by the router
C.The Seria l0/0 interf aceacquired the IP address of 172.16.3.1 from a DHCP server
D.The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud
E.The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
A.can be used over analog circuits
B.maps Layer 2 to Layer 3 address
C.encapsulates several routed protocols
D.supports IP only
E.provides error correction
A.point-to-point
B.broadcast multi-access
C.nonbroadcast multi-access
D.nonbroadcast multipoint.broadcast point-to-multipoint
Refer to the exhibit.Which statement describes DLCI 17?（）
A.DLCI 17 describes the ISDN circuit between R2 and R3.
B.DLCI 17 describes a PVC on R2.It cannot be used on R3 or R1.
C.DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D.DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.
最新試題
什么問題導致SERVER VTP密碼跟替他交換機VTP密碼不匹配？
Which of the following describes the roles of devices in a WAN?（）
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2.The routers cannot establish an adjacency relationship on their common Ethernet link.The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.Based on the information in the graphic,what is the cause of this problem?（）
The following configuration line was added to router R1 Access-list 101 permit ip 10.25.30.00.0.0.255 any What is the effect of this access list configuration?（）
What field in IP packet is used for classification by QOS？
What is method list for configure aaa？
How should arouter that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?（）
一堆交換機一個server、一個transpare，問配置prune在哪里配置？
SPT初始狀態之后的一個狀態是什么？
What is the three main step of using the QoS feature with MQC command line interface？