A. Never use passive interfaces.
B. Use NSSA areas from the core down.
C. Use totally stub areas to stop type 3 LSAs.
D. Use the lowest Ethernet interface IP address as the router ID.
E. Tune OSPF timers to enable OSPF to achieve quicker convergence.
您可能感興趣的試卷
你可能感興趣的試題
A. Server-to-server traffic always remains in the core layer.
B. The recommended practice is for the core infrastructure to be in Layer 3.
C. The boundary between Layer 2 and Layer 3 should be implemented in the aggregation layer.
D. The Cisco Express Forwarding hashing algorithm is the default, based on the IP address and Layer 4 port.
E. Core layer should run BGP along with an IGP becauseiBGP has a lower administrative distance than any IGP.
A.ASM
B.BiDirPIM
C.PIM-SMRP
D.RP-Switchover
E.SourceSpecificMulticast
A. 0
B. 1
C. 2
D. 4
E. 16
F. infinity
A. a single host
B. a subset of hosts
C. all hosts sequentially
D. all hosts simultaneously
A.TCP502
B.TCP514
C.TCP520
D.UDP502
E.UDP514
F.UDP520
A. supports multiple MIBs
B. includesNetFlow, NBAR, and IP SLA software subsystems
C. includesNetFlow, syslog, and IP SLA software subsystems
D. includes a predefined framework for filtering and correlating messages
E. supports two logging processes so output can be sent in standard and ESM format
A. to provide service internetworking
B. to support transparency for Layer 2 frames
C. as a connection identifier to indicate destination
D. as a mapping to the DLCI in service internetworking
E. to provide a trunk by which all VLANs can navigate from one site to one or multiple sites
A. use BGP as the CE-PE routing protocol
B. use OSPF as the CE-PE routing protocol
C. use EIGRP as the CE-PE routing protocol
D. use the SP to redistribute routes as external routes for OSPF and EIGRP
E. use route redistribution at each location to ensure external routes are imported into the IGP
A. Layer 3 MPLS VPNs can forward only IP packets
B. Layer 2 MPLS VPNs can forward any network protocol
C. MPLS label paths are automatically formed based on Layer 2 frames
D. Layer 3 MPLS VPNs can forward any network protocol based on Layer 2 frames
E. In Layer 2 MPLS VPNS, the service provider controls the customer Layer 3 policies
A.DPT
B.MPLS
C.VPLS
D.CWDM
E. DWDM
F. SONET/SDH
最新試題
You are the Cisco Network Designer . Which is not major scaling, sizing, and performance consideration for an IPsec design?（）
As an experienced technician, you are responsible for Technical Support. One of the trainees is asking your advice on VPN Termination Device and Firewall Placement. Which of the following approaches will you recommend?（）
In which NAS operating mode are ACL filtering and bandwidth throttling only provided during posture assessment?（）
What is the term for a logical SAN which provides isolation among devices physically connected to the same fabric?（）
In a VoWLAN deployment, what is the recommended separation between cells with the same channel?（）
As an experienced technician, you are responsible for Technical Support. Which of the following descriptions is correct about the characteristic of SLB one arm mode?（）
You are the network consultant from pass4sure.com. One of your customer has six sites, three of which process a large amount of traffic among them. He plans to grow the number of sites in the future. Which is the most appropriate design topology?（）
Which of these is a benefit of using Network Admission Control instead of Cisco Identity Based Networking Services?（）
Please match the Cisco STP enahancement term to its definition.（）(1) BPDU guard(2) PortFast(3) BackboneFast(4) Loop guard(5) Root guard(a) shuts down a port that receives a BPDU when enabled(b) cuts convergence time by mas-age for indirect failure(c) prevents the aliernate or root port from being designated in absence of BPDUs(d )causes Layer 2 LAN interface access port to immediately enter the forwarding state(e) helps prevent bridging loops due to jni-directional link failures on point-to-point links
During consultation, you find that a customer has multiple asset closets and will be adding more in the future. Which NAS physical deployment model would you suggest to this customer?（）