Routers R1 and R2 are configured for HSRP as shown below：
Router R1：
interface ethernet 0
ip address 20.6.2.1 255.255.255.0
standby 35 ip 20.6.2.21
standby 35 priority 100
interface ethernet 1
ip address 20.6.1.1.2 255.255.255.0
standby 34 ip 20.6.1.21
Router R2：
interface ethernet 0
ip address 20.6.2.2 255.255.255.0
standby 35 ip 20.6.2.21
interface ethernet 1
ip address 20.6.1.1.1 255.255.255.0
standby 34 ip 20.6.1.21
standby 34 priority 100
You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）
A.physical layer issues
B.no spanning tree loops
C.use of non-default HSRP timers
D.failure to set the command standby 35 preempt
您可能感興趣的試卷
你可能感興趣的試題
A.It can be used to block bulk encryption attacks
B.It can be used to protect against denial of service attacks
C.Traffic originating from the router is considered trusted， so it is not inspected
D.Based upon the custom firewall rules， an ACL entry is statically created and added to theexisting ACL permanently
E.Temporary ACL entries that allow selected traffic to pass are created and persist for theduration of the communication session
Refer to the exhibit. Host A has sent an ARP message to the default gateway IP address10.10.10.1. Which statement is true？（）
A.DSw1 will reply with the MAC address of the next AVF
B.DSw2 will reply with the MAC address of the next AVF
C.Because of the invalid timers that are configured， DSw1 will not reply
D.Because of the invalid timers that are configured， DSw2 will not reply
E.DSw1 will reply with the IP address of the next AVF
F.DSw2 will reply with the IP address of the next AVF
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDM， click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDM， you can return to yourquestions by clicking on the Questions button to the left.
Off Shore Industries is a large worldwide sailing charter. The company has recently upgraded itsInternet connectivity. As a recent addition to the network engineering team， you have been taskedwith documenting the active Firewall configurations on the Annapolis router using the Cisco Routerand Security Device Manager （SDM） utility.
Using the SDM output from Firewall and ACL Tasks under the Configure tab， answer the followingquestions：
Which two statements would specify a permissible incoming TCP packet on a trusted interface inthis configuration？（）
A.The packet has a source address of 10.79.233.107
B.The packet has a source address of 172.16.81.108
C.The packet has a source address of 198.133.219.40
D.The destination address is not specified within the inspection rule SDM_LOW
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDM， click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDM， you can return to yourquestions by clicking on the Questions button to the left.
Off Shore Industries is a large worldwide sailing charter. The company has recently upgraded itsInternet connectivity. As a recent addition to the network engineering team， you have been taskedwith documenting the active Firewall configurations on the Annapolis router using the Cisco Routerand Security Device Manager （SDM） utility. Using the SDM output from Firewall and ACL Tasksunder the Configure tab， answer the following questions：
Which statement is true？（）
A.Both FastEthernet 0/0 and Serial 0/0/0 are trusted interface
B.Both FastEthernet 0/0 and Serial 0/0/0 are untrusted interfaces
C.FastEthernet 0/0 is a trusted interface and Serial 0/0/0 is an untrusted interface
D.FastEthernet 0/0 is an untrusted interface and Serial 0/0/0 is a trusted interface
A.Spanning Tree Protocol （STP）
B.Delay reduction
C.Hot Standby Routing Protocol （HSRP）
D.Dynamic routing protocols
E.Quality of Service （QoS）
F.Jitter management
What can be determined about the HSRP relationship from the displayed debug output？（）
A.Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router172.16.11.112
B.The IP address 172.16.11.112 is the virtual HSRP router IP address
C.The nonpreempt feature is enabled on the 172.16.11.112 router
D.The IP address 172.16.11.111 is the virtual HSRP router IP address
E.Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router172.16.11.111
F.The preempt feature is not enabled on the 172.16.11.111 router
Examine the router output above. Which two items are correct？（）
A.If Ethernet 0/2 goesdown， the standby router will take over
B.The local IP address of Router A is 10.1.0.6
C.When Ethernet 0/3 of RouterA comes back up， the priority will become 105
D.Router A will assume the active state if its priority is the highest
E.The local IP address of Router A is 10.1.0.20
Refer to the exhibit. Based upon the debug output that is shown， which three statements aboutHSRP are true？（）
A.The router with IP address 172.16.11.112 is using default HSRP priority
B.The IP address 172.16.11.115 is the virtual HSRP IP address
C.The priority of the router with IP address 172.16.11.112 is preferred over the router with IPaddress 172.16.11.111
D.The router with IP address 172.16.11.111 haspreempt configured
E.The final active router is the router with IP address 172.16.11.111
F.The router with IP address 172.16.11.112 has nonpreempt configured
Refer to the exhibit. Which two problems are the most likely cause of the exhibited output？（）
A.VRRP misconfiguration
B.spanning tree issues
C.transport layer issues
D.physical layer issues
E.HSRP misconfiguration
Examine the router output above. Which two items are correct？（）
A.If Ethernet 0/2 goesdown， the standby router will take over
B.The local IP address of Router A is 10.1.0.6
C.When Ethernet 0/3 of RouterA comes back up， the priority will become 105
D.Router A will assume the active state if its priority is the highest
E.The local IP address of Router A is 10.1.0.20
最新試題
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Which statement about PPPoA configuration is correct？（）
Which statement correctly describes IPsec VPN backup technology？（）
Study the exhibit carefully.Routers A and B are customer routers. Routers 1， 2， 3 and 4 are provider routers. The routers areoperating with various IOS versions. Which frame mode MPLS configuration statement is true？（）
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.