A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:
TK1(config)# router ospf 1
TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0
After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）
A. The AS is not correctly configured
B. The network subnet mask is incorrectly configured
C. The network wildcard mask is configured incorrectly
D. The network number is not correctly configured
E. The process id is configured incorrectly
F. None of the above
您可能感興趣的試卷
你可能感興趣的試題
On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:
What is the underlying cause of the routers failing to become adjacent?（）
A. The OSPF area is misconfigured.
B. The priority on TK2 should be set lower.
C. The cost on TK2 should be set lower.
D. The hello and dead timers are misconfigured.
E. You need to add a backup designated router to the network.
F. The OSPF process ID numbers do not match.
While trying to diagnose a routing problem in the network, you issue RIP debugging as displayed below:
RtrA#debug ip rip
Rip protocol debugging is on
RtrA#
1d05h: RIP: sending v1 update to 255.255.255.255 via FastEthernet0/0 (172.16.1.1)
1d05h: RIP: build update entries
1d05h: network 10.0.0.0 metric 1
1d05h: network 192.168.1.0 metric 2
1d05h: RIP: sending v1 update to 255.255.255.255 via Serial0/0 (10.0.8.1)
1d05h: RIP: build update entries
1d05h: network 172.16.0.0 metric 1
RtrA#
1d05h: RIP: received v1 update from 10.0.15.2 on Serial0/0
1d05h: 192.168.1.0 in 1 hops
1d05h: 192.168.0 in 16 hops (inaccessible)
Based on the output of the above exhibit, which two of the following statements are true?（）
A. A ping to 10.0.15.2 will be successful.
B. RtrA has three interfaces that will take part in the RIP process.
C. There are at least two routers participating in the RIP process.
D. A ping to 192.168.168.2 will be successful.
A. TK1# show ip ospf interface
B. TK1# show ip ospf priority
C. TK1# show ospf neighbor detail
D. TK1# show ospf processes
E. TK1# show ospf neighbor state
A. Each end of the trunk line must be set to IEEE 802.1E encapsulation.
B. The VTP management domain name of both switches must be set the same.
C. All ports on both the switches must be set as access port.
D. One of the two switches must be configured as a VTP server.
E. A rollover cable is required to connect the two switches together.
F. A router must be used to forward VTP traffic between VLANs.
A. Ping
B. Tracert
C. Ipconfig
D. Show ip route
E. Winipcfg
F. Show interfaces
A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfg
F. show interfaces
G. All of the above
A. ping
B. tracert
C. netstat
D. show cdp neighbors detail
E. show ip route
F. traceroute
A. The switch port link lights will be off on both switches indicating the ports are not connected.
B. The switch port link light will be off on one switch indicating that STP has disabled the port.
C. The switch port link lights will flash amber indicating an error.
D. The switch port link lights will be green indicating normal operation.
A. show ip route
B. ipconfig
C. tracert
D. show interfaces
E. traceroute
F. ping
G. All of the above
Study the Exhibit below carefully:
London#show vtp
VTP Version: 2
Configuration Revision: 0
Maximum VLANs supported locally: 64
Number of existing VLANs: 5
VTP Operating Mode: Client
VTP Domain Name: London
VTP Pruning Mode: Disabled
VTP V2 Mode: Disabled
VTP Traps Generation: Disabled
Based on the information given above, what is the VTP function of this particular switch?（）
A. Learn and save VTP configuration in the running configuration.
B. Create and change VLANs.
C. Forwards information about VTP configuration.
D. VTP is disabled on this device.
E. VTP is not saved to NVRAM.
最新試題
Which of the following describe router functions?（）
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? （）
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）
What feature of a networks switch allows an administrative to create separate broadcast domains?（）
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?（）
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?（）
Which of the following correctly describe steps in the OSI data encapsulation process?（）
A Class C network address has been subnetted with a /27 mask.Which of the following addresses is a broadcast address for one of the resulting subnets?（）
What is a global command?（）
What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?（）