A switch port on TK1 is being configured to support 802.1Q trunking.
Which of the following are true about 802.1Q trunking？（）
A.Both switches must be in the same VTP domain.
B.The encapsulation type of both ends of the trunk does not have to match.
C.The native VLAN on both ends of the trunk must be VLAN 1.
D.802.1Q trunking can only be configured on a Layer 2 port.
E.In 802.1Q trunking， all VLAN packets are tagged on the trunk link， except the native VLAN.
您可能感興趣的試卷
你可能感興趣的試題
A.forwarding information base
B.adjacency tables
C.neighbor tables
D.caching tables
E.route tables
A.Address Resolution Protocol （ARP）
B.PDU header rewrite
C.NetFlow switching
D.hello packet exchange
A.Switch（config-if）#spanning-tree guard root
B.Switch（config-if）#spanning-tree portfast
C.Switch（config-if）#switchport mode trunk
D.Switch（config-if）#switchport mode access
A port in a redundant topology is currently in the blocking state and is not receiving BPDUs. To ensure that this port does not erroneously transition to the forwarding state，
which command should be configured to satisfy the requirement？（）
A.Switch（config）#spanning-tree loopguard default
B.Switch（config-if）#spanning-tree bdpufilter
C.Switch（config）#udld aggressive
D.Switch（config-if）#spanning-tree bpduguard
A.spanning-tree guard root
B.spanning-tree portfast bpduguard default
C.spanning-tree bpduguard enable
D.spanning-tree bpdufilter enable
E.spanning-tree portfast bpdufilter default
A.a native VLAN mismatch on either side of an 802.1Q link
B.BPDU filter configured on a link to another switch
C.Spanning Tree Protocol enabled on both Layer 2 and multilayer switches
D.PortFast enabled on all access and trunk ports
A.Configuration changes made on the port-channel interface apply to all physical ports assigned to the portchannel interface.
B.Configuration changes made on a physical port that is a member of a port-channel interface apply to the port-channel interface.
C.Configuration changes are not permitted with Port Aggregation Protocol； instead， the standardized Link Aggregation Control Protocol should be used if configuration changes are required.
D.The physical port must first be disassociated from the port-channel interface before any configuration changes can be made.
A.no switchport trunk native vlan vlan-id
B.switchport nonegotiate
C.no switchport mode dynamic desirable
D.switchport mode access
A.switchport dynamic auto switchport dynamic auto
B.switchport access vlan 10 switchport mode dynamic desireable
C.switchport mode trunk switchport nonegotiate
D.Leave both ports with the default trunk settings
A.By default， native VLAN packets going out this port will be tagged.
B.Without an encapsulation command， 802.1Q will be the default encapsulation if DTP fails to negotiate a trunking protocol.
C.The interface will support the reception of tagged and untagged traffic.
D.If the device connected to this port is not 802.1Q-enabled， it will not be able to handle 802.1Q packets.
最新試題
Which three statements about STP timers are true？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）