A.registration error
B.authentication failures threshold
C.http disabled
D.telnet disabled
您可能感興趣的試卷
你可能感興趣的試題
A.administrators
B.system monitoring
C.network operator
D.power users
E.admin
F.users’ assistant
When configuring vlans on an autonomous access point.
What must be configured on the connected switchport？（）
A.802.1q trunking
B.vtp trunking
C.isl trunking
D.dpt trunking
There are 30 managed access points on the wlse. a radio scan is started but fails. Upon
inspection of the device list in the reports tab， you notice a red indicator on the wds access point. upon inspection of the wds access point through its guid， it is discovered that the security keys are not set up between the wds access point and the wlse.
Which of the following is mis configured？（）
A.snmp communities
B.telnet/ssh user/password
C.wlccp credentials
D.http user/password
You are using adu and are authenticated and associated to an access point. you are unable to obtain an ip address.
Which of the following will cause this problem？（）
A.aes encryption enabled
B.tkip enabled
C.third-party wireless supplicant enabled
D.802.1x authentication type enabled
On a series 1010 lightweight access point， the alarm led is flashing red， and all other leds are off.
What is the lightweight access point indicating？（）
A.it has lost contact with controller.
B.its ip address already exists.
C.it requires a code upgrade.
D.it is operating normally.
A.router# show wlccp ap
B.router# show wlccp wds ap
C.router# show wlccp cckm
D.router# show wlccp wds cckm
A.dictionary
B.bit-flip and replay
C.mac spoofing
D.man-in-the-middle
A.https
B.tftp
C.rmi
D.http
E.ftp
A.shut down rogue access points
B.configure access points
C.discover access points
D.inventory access points
Using the wlse,you are trying to push out a configuration job to an access point,but the job does not start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect snmp communities on the access point
C.unsupported version of ios firmware in the access point
D.pop-up blocker enabled in the browser
最新試題
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）