A.registration error
B.authentication failures threshold
C.HTTP disabled
D.Telnet disabled
您可能感興趣的試卷
你可能感興趣的試題
A.802.1q trunking
B.VTP trunking
C.ISL trunking
D.DPT trunking
There are 30 managed access points on the WLSE. A radio scan is started but fails. Upon inspection of the device list in the reports tab， you notice a red indicator on the WDS access point.Upon inspection of the WDS access point through its GUI， it is discovered that the security keys arenot set up between the WDS access point and the WLSE.
Which of the following is misconfigured？（）
A.SNMP communities
B.Telnet/SSH user/password
C.WLCCP credentials
D.HTTP user/password
You are using ADU and are authenticated and associated to an access point. You are unable toobtain an IP address.
Which of the following will cause this problem？（）
A.AES encryption enabled
B.TKIP enabled
C.third-party wireless supplicant enabled
D.802.1X authentication type enabled
On a Series 1010 lightweight access point， the alarm LED is flashing red， and all other LEDs are off.
What is the lightweight access point indicating？（）
A.It has lost contact with controller.
B.Its IP address already exists.
C.It requires a code upgrade.
D.It is operating normally.
A.router# show wlccp ap
B.router# show wlccp wds ap
C.router# show wlccp cckm
D.router# show wlccp wds cckm
A.HTTPS
B.TFTP
C.RMI
D.HTTP
E.FTP
A.SSIDs are not case sensitive.
B.SSIDs must be listed in the same order in the ADU as they are in the access point.
C.A maximum of three SSIDs may be configured.
D.SSIDs may have a maximum of 16 characters.
Using the WLSE，you are trying to push out a configuration job to an access point，but the job doesnot start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.unsupported version of IOS firmware in the access point
D.pop-up blocker enabled in the browser
A.75
B.100
C.25
D.50
Client association using EAP-Cisco Wireless （LEAP） is failing， but EAP-PEAP is functioning on an autonomous access point.
Which of the following needs to be enabled on the access point so EAP-Cisco Wireless （LEAP） is enabled？（）
A.open authentication plus MAC
B.open authentication plus EAP
C.shared key
D.network EAP
最新試題
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）