A. VT circuits
B. STS circuits
C. VT tunnel circuits
D. 1:1 protection circuits
E. 1:N protection circuits
您可能感興趣的試卷
你可能感興趣的試題
Click the Exhibit button. Given the information shown in the exhibit, when creating 2 DS1 circuits, how many STS ports are used on the VT1.5 matrix at Node 1 as VT circuits and how many are used after using VT tunnels?（）
A.2；0
B.3；2
C.3；5
D.4；0
E.6；0
F.6；2
A. Slot 2 and Slot 4
B. Slot 4 and Slot 6
C. Slots 5 or 13 only
D. Slot 16 and Slot 17
Click the Exhibit button. Which type of protection is shown in the exhibit?（）
A.1+0
B.1+1
C.1：1
D.1：N
A.0
B.1
C.2
D.3
E.4
A. signal fail, signal degrade, manual switch
B. signal degrade, signal fail, manual switch
C. protection lockout, manual switch, path AIS
D. forced switch, manual switch, signal degrade
E. protection lockout, manual switch, forced switch
A. Switch times would exceed 50 ms for an OC-3 BLSR ring.
B. An equal amount of working and protect bandwidth is required.
C. DCC bandwidth is not large enough to handle K1/K2 processing.
D. There is not enough bandwidth in an OC-3 ring to justify BLSR protection.
A. It protects signals against node failures between rings.
B. It protects signals against node failure within a single ring.
C. It allows for traffic to be preempted when a ring switch occurs.
D. Traffic can be dropped and continued at interconnecting nodes.
E. It protects preemptible traffic from being dropped when a ring switch occurs.
A.LEX
B.HDLC
C.GFP-F
D.PPP/BCP
Click the Exhibit button. In the DCN connection shown in the exhibit, all non-GNE nodes are located on different subnets from the GNE. There are no static routes or external OSPF on any elements. CTC Workstation and GNE have Cisco Router as their default gateway.
Can the CTC workstation see the entire SONET network?（）
A. Yes, but only if OSPF is enabled around the ring.
B. Yes, because the GNE will only serve as a proxy-ARP for elements on the same subnet.
C. Yes, but only if the router's address is entered as a static route in the non-GNE elements.
D. Yes, because the GNE will serve as a proxy-ARP for all elements, regardless of their subnets.
A. line timing
B. loop timing
C. internal timing
D. through timing
E. external timing
最新試題
How is a Thin Film filter fabricated?（）
What protection method is used in 4F BLSR networks?（）
A Channel ID mismatch occurs when （）.
What three in combination are factors that can cause four-wave mixing in fiber-optic cables? （）(Choose three.)
What is the phenomenon called where different wavelengths of light travel at different speeds?（）
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? （）(Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.)
Click the Exhibit button. Which type of multiplexer is shown in the exhibit?（）
What are three factors that limit the maximum distance of an amplified optical signal without regeneration? （）(Choose three.)
If the power is 0 dBm, what is the power in mW?（）
The ONS 15216 is a 32-channel system. The ONS 15216 OADMs are capable of adding and dropping one, two, or four channels. How are the OADMs provisioned to add and drop specific channels?（）