A. They are both regions of lowest loss.
B. They are both regions of low reflections.
C. They are both regions of low index of refraction.
D. They are both regions of low chromatic dispersion.
E. They are both regions of low Polarization Mode Dispersion (PMD).
您可能感興趣的試卷
你可能感興趣的試題
A. lower cost
B. higher chirp
C. easier to manufacture
D. higher dispersion tolerance
E. higher optical signal-to-noise ratio
A. OSNR
B. dispersion
C. attenuation
D. power budget
E. amplifier spacing
F. four wave mixing
A. PIN photodiodes
B. zero-chirped lasers
C. Erbium-doped fiber amplifiers
D. dispersion compensating fiber
E. dispersion compensating Bragg grating
A.OSNR
B.dispersion
C.light skew
D.attenuation
A.none
B.one
C.two
D.three
E.four
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? ()(Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.)
A.15dB
B.17dB
C.21dB
D.26dB
E.27dB
A. All "Add" channels require uniform power levels.
B. The flexibility of wavelengths per OADM is limited.
C. It is easier to balance "Pass-Through" and "Add" channels.
D. There is lower pass-through loss using multi-channel OADMs.
E. You can extract a single channel without dropping other channels.
Click the Exhibit button. Given the following parameters: transmitter output (min): -2 dBm receiver input (min): -28 dBm 15216 Mux and Demux loss: 4.5 dB 16 channels maximum In which sites shown in the exhibit could the 15216 EDFAs be placed to minimize the number of EDFAs needed?()
A. Locations B, C only
B. Locations A, B, C only
C. Locations A, B, D only
D. Locations B, C, D only
E. Locations A, B, C, D
A. The ONS 15216 OADM can be provisioned to add/drop one, two, or four channels via Cisco Transport Manager (CTM).
B. The ONS 15216 OADM consists only of a four-channel module, and the number of ports utilized determines whether it is a one, two, or four channel OADM.
C. Three separate OADM modules are available for one, two, and four channels. The wavelengths to be dropped and added are programmable via Cisco Transport Manager (CTM).
D. The ONS 15216 OADM consists only of a single-channel module. Two-channel and four-channel support is available by stacking the single-channel module.
E. The ONS 15216 OADM is available in one, two, four channels. There are 32 single-channel OADM modules, 16 two-channel OADM modules, and 8 four-channel OADM modules.
Click the Exhibit button. The exhibit shows a 15454/15216 DWDM system and alarm indications. What are two possible sources of trouble shown in the system?() (Choose two.)
A. fiber failure between Sites A and d
B. EDFA failure at Site A (clockwise direction)
C. EDFA failure at Site C (clockwise direction)
D. 15216 multiplexer at Site A (counter-clockwise direction)
E. OADM pass-through (West "OUT") failure at site D (clockwise)
F. wavelengths 1 and 3 transmitter failures at Site A (clockwise direction)
最新試題
Which is a legitimate bandwidth matched pair?()
What is the difference between the transmitted power and the sensitivity of the receiver?()
Click the Exhibit button. What is the maximum allowable loss budget between the ONS 15216 Mux (left side) composite output and the ONS 15216 Demux (right side) composite input, with the optical values given in the exhibit? ()(Assume the worst case loss of 4.5 dB for 15216 200 GHz Mux/Demux and ignore power penalties or extra margin.)
If node 2 is accepting line timing from node 1, node 2 will send ()to node 1 as its SSM message.
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to (). (Choose three.)
In the OSNR model for EDFA amplifiers, SNR OUT = 1/(1/SNR IN + FhvB/P IN ), what does SNR IN represent?()
Why are the 1300 nm and 1550 nm regions of the fiber spectrum primarily used for optical communications?()
What is an advantage of an externally modulated laser over a directly modulated laser?()
UPSR protection switching is initiated by (), while BLSR is initiated by ().
How is a Thin Film filter fabricated?()