多項選擇題What are two important considerations when using 2- or 4-channel 15216 OADMs?（） (Choose two.)

A. All "Add" channels require uniform power levels.
B. The flexibility of wavelengths per OADM is limited.
C. It is easier to balance "Pass-Through" and "Add" channels.
D. There is lower pass-through loss using multi-channel OADMs.
E. You can extract a single channel without dropping other channels.


您可能感興趣的試卷

你可能感興趣的試題

2.單項選擇題The ONS 15216 is a 32-channel system. The ONS 15216 OADMs are capable of adding and dropping one, two, or four channels. How are the OADMs provisioned to add and drop specific channels?（）

A. The ONS 15216 OADM can be provisioned to add/drop one, two, or four channels via Cisco Transport Manager (CTM).
B. The ONS 15216 OADM consists only of a four-channel module, and the number of ports utilized determines whether it is a one, two, or four channel OADM.
C. Three separate OADM modules are available for one, two, and four channels. The wavelengths to be dropped and added are programmable via Cisco Transport Manager (CTM).
D. The ONS 15216 OADM consists only of a single-channel module. Two-channel and four-channel support is available by stacking the single-channel module.
E. The ONS 15216 OADM is available in one, two, four channels. There are 32 single-channel OADM modules, 16 two-channel OADM modules, and 8 four-channel OADM modules.

3.多項選擇題

Click the Exhibit button. The exhibit shows a 15454/15216 DWDM system and alarm indications. What are two possible sources of trouble shown in the system?（） (Choose two.)

A. fiber failure between Sites A and d 
B. EDFA failure at Site A (clockwise direction)
C. EDFA failure at Site C (clockwise direction)
D. 15216 multiplexer at Site A (counter-clockwise direction)
E. OADM pass-through (West "OUT") failure at site D (clockwise)
F. wavelengths 1 and 3 transmitter failures at Site A (clockwise direction)

4.多項選擇題What are three relevant design considerations when using the 15216 EDFA? （）(Choose three.)

A. dispersion
B. Optical SNR
C. span attenuation
D. four wave mixing
E. receiver sensitivity

5.單項選擇題UPSR protection switching is initiated by （）, while BLSR is initiated by （）.

A. the K1 SONET byte； the K2 SONET byte
B. the K2 SONET byte；the K1 SONET byte
C. transmitter switching；receiver detection
D. Line Overhead bytes；Path Overhead bytes
E. Path Overhead bytes；Line Overhead bytes

6.單項選擇題On an ONS 15454 node you can tunnel an （）.

A. SDH circuit over a SONET network delivering it as an SDH signal
B. SDH circuit over a SONET network delivering it as a SONET signal
C. SONET circuit over an SDH network delivering it as an SDH signal
D. SONET circuit over an SDH network delivering it as a SONET signal

8.單項選擇題How is UPSR and BLSR traffic rerouted during a protection switch when a complete fiber cable cut occurs?（）

A. Traffic is switched from the first node receiving the AIS indication.
B. Traffic is switched from the far side of the failure, allowing handshaking to occur.
C. UPSR traffic is switched from the terminating node, BLSR traffic is rerouted from the originating node in the ring.
D. UPSR traffic is switched from the terminating node, circuit by circuit. BLSR traffic is rerouted from the last reachable node in the ring.

9.單項選擇題What protection method is used in 4F BLSR networks?（）

A. Each fiber has half of its SONET capacity reserved for protection.
B. Two fibers in the span carry working traffic, while the other two fibers in the span are reserved for protection.
C. The signal is sent simultaneously in both directions around the ring. The receiver determines which fiber to listen to based on signal quality.
D. The signal is sent simultaneously in both directions around the ring. The transmitter determines which fiber has the working bit set for the receiver to acknowledge.

10.單項選擇題Which is a legitimate bandwidth matched pair?（）

A. DS-1; E1
B. DS-1; STM-1
C. OC-3; STM-1
D. STS-1; STM-1
E. OC-192; STM-192